Network Working Group Y. Rekhter
Request for Comments: 3107 Juniper Networks
Category: Standards Track E. Rosen
Cisco Systems, Inc.
May 2001
Carrying Label Information in BGP-4
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2001). All Rights Reserved.
Abstract
This document specifies the way in which the label mapping
information for a particular route is piggybacked in the same Border
Gateway Protocol (BGP) Update message that is used to distribute the
route itself. When BGP is used to distribute a particular route, it
can be also be used to distribute a Multiprotocol Label Switching
(MPLS) label which is mapped to that route.
Table of Contents
1 Specification of Requirements .......................... 2
2 Overview ............................................... 2
3 Carrying Label Mapping Information ..................... 3
4 Advertising Multiple Routes to a Destination ........... 4
5 Capability Advertisement ............................... 4
6 When the BGP Peers are not Directly Adjacent ........... 5
7 Security Considerations ................................ 5
8 Acknowledgments ........................................ 6
9 References ............................................. 6
10 Authors' Addresses ..................................... 7
11 Full Copyright Statement ............................... 8
Rekhter & Rosen Standards Track [Page 1]
RFC 3107 Carrying Label Information in BGP-4 May 2001
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119.
When BGP is used to distribute a particular route, it can also be
used to distribute an MPLS label that is mapped to that route [MPLS-
ARCH]. This document specifies the way in which this is done. The
label mapping information for a particular route is piggybacked in
the same BGP Update message that is used to distribute the route
itself.
This can be useful in the following situations:
- If two immediately adjacent Label Switched Routers (LSRs) are
also BGP peers, then label distribution can be done without the
need for any other label distribution protocol.
- Suppose one's network consists of two "classes" of LSR:
exterior LSRs, which interface to other networks, and interior
LSRs, which serve only to carry traffic between exterior LSRs.
Suppose that the exterior LSRs are BGP speakers. If the BGP
speakers distribute MPLS labels to each other along with each
route they distribute, then as long as the interior routers
support MPLS, they need not receive any of the BGP routes from
the BGP speakers.
If exterior router A needs to send a packet to destination D,
and A's BGP next hop for D is exterior router B, and B has
mapped label L to D, then A first pushes L onto the packet's
label stack. A then consults its IGP to find the next hop to
B, call it C. If C has distributed to A an MPLS label for the
route to B, A can push this label on the packet's label stack,
and then send the packet to C.
If a set of BGP speakers are exchanging routes via a Route Reflector
[BGP-RR], then by piggybacking the label distribution on the route
distribution, one is able to use the Route Reflector to distribute
the labels as well. This improves scalability quite significantly.
Note that if the Route Reflector is not in the forwarding path, it
need not even be capable of forwarding MPLS packets.
Label distribution can be piggybacked in the BGP Update message by
using the BGP-4 Multiprotocol Extensions attribute [RFC 2283]. The
label is encoded into the NLRI field of the attribute, and the SAFI
Rekhter & Rosen Standards Track [Page 2]
RFC 3107 Carrying Label Information in BGP-4 May 2001
("Subsequent Address Family Identifier") field is used to indicate
that the NLRI contains a label. A BGP speaker may not use BGP to
send labels to a particular BGP peer unless that peer indicates,
through BGP Capability Advertisement, that it can process Update
messages with the specified SAFI field.
Label mapping information is carried as part of the Network Layer
Reachability Information (NLRI) in the Multiprotocol Extensions
attributes. The AFI indicates, as usual, the address family of the
associated route. The fact that the NLRI contains a label is
indicated by using SAFI value 4.
The Network Layer Reachability information is encoded as one or more
triples of the form <length, label, prefix>, whose fields are
described below:
+---------------------------+
| Length (1 octet) |
+---------------------------+
| Label (3 octets) |
+---------------------------+
.............................
+---------------------------+
| Prefix (variable) |
+---------------------------+
The use and the meaning of these fields are as follows:
a) Length:
The Length field indicates the length in bits of the address
prefix plus the label(s).
b) Label:
The Label field carries one or more labels (that corresponds to
the stack of labels [MPLS-ENCAPS]). Each label is encoded as 3
octets, where the high-order 20 bits contain the label value,
and the low order bit contains "Bottom of Stack" (as defined in
[MPLS-ENCAPS]).
c) Prefix:
The Prefix field contains address prefixes followed by enough
trailing bits to make the end of the field fall on an octet
boundary. Note that the value of trailing bits is irrelevant.
Rekhter & Rosen Standards Track [Page 3]
RFC 3107 Carrying Label Information in BGP-4 May 2001
The label(s) specified for a particular route (and associated with
its address prefix) must be assigned by the LSR which is identified
by the value of the Next Hop attribute of the route.
When a BGP speaker redistributes a route, the label(s) assigned to
that route must not be changed (except by omission), unless the
speaker changes the value of the Next Hop attribute of the route.
A BGP speaker can withdraw a previously advertised route (as well as
the binding between this route and a label) by either (a) advertising
a new route (and a label) with the same NLRI as the previously
advertised route, or (b) listing the NLRI of the previously
advertised route in the Withdrawn Routes field of an Update message.
The label information carried (as part of NLRI) in the Withdrawn
Routes field should be set to 0x800000. (Of course, terminating the
BGP session also withdraws all the previously advertised routes.)
A BGP speaker may maintain (and advertise to its peers) more than one
route to a given destination, as long as each such route has its own
label(s).
The encoding described above allows a single BGP Update message to
carry multiple routes, each with its own label(s).
In the case where a BGP speaker advertises multiple routes to a
destination, if a route is withdrawn, and a label(s) is specified at
the time of withdrawal, only the corresponding route with the
corresponding label is withdrawn. If a route is withdrawn, and no
label is specified at the time of withdrawal, then only the
corresponding unlabeled route is withdrawn; the labeled routes are
left in place.
A BGP speaker that uses Multiprotocol Extensions to carry label
mapping information should use the Capabilities Optional Parameter,
as defined in [BGP-CAP], to inform its peers about this capability.
The MP_EXT Capability Code, as defined in [BGP-MP], is used to
advertise the (AFI, SAFI) pairs available on a particular connection.
A BGP speaker should not advertise this capability to another BGP
speaker unless there is a Label Switched Path (LSP) between the two
speakers.
Rekhter & Rosen Standards Track [Page 4]
RFC 3107 Carrying Label Information in BGP-4 May 2001
A BGP speaker that is capable of handling multiple routes to a
destination (as described above) should use the Capabilities Optional
Parameter, as defined in [BGP-CAP], to inform its peers about this
capability. The value of this capability is 4.
Consider the following LSR topology: A--B--C--D. Suppose that D
distributes a label L to A. In this topology, A cannot simply push L
onto a packet's label stack, and then send the resulting packet to B.
D must be the only LSR that sees L at the top of the stack. Before A
sends the packet to B, it must push on another label, which was
distributed by B. B must replace this label with yet another label,
which was distributed by C. In other words, there must be an LSP
between A and D. If there is no such LSP, A cannot make use of label
L. This is true any time labels are distributed between non-adjacent
LSRs, whether that distribution is done by BGP or by some other
method.
This document does NOT specify any procedure for ensuring in real
time that label distribution between non-adjacent LSRs is done only
when the appropriate MPLS infrastructure exists in the network or
networks connecting the two LSRs. Ensuring that the proper
infrastructure exists is an issue for network management and
operation.
When an LSR A is directly connected to an LSR B via a point-to-point
interface, then when A receives packets over that interface, it knows
that they come from B. This makes it easy for A to discard any
packets from B whose top labels are not among the labels that A
distributed to B. That is, A can easily ensure that B only uses
those labels which it is entitled to use. This technique can be used
to prevent "label spoofing", i.e., the situation in which an LSR
imposes a label which has not been properly distributed to it.
The procedures discussed in this document would commonly be used when
the label distribution peers are separated not merely by a point-to-
point link, but by an MPLS network. This means that when an LSR A
processes a labeled packet, it really has no way to determine which
other LSR B pushed on the top label. Hence it cannot tell whether
the label is one which B is entitled to use. In fact, when Route
Reflectors are in use, A may not even know the set of LSRs which
receive its label mappings. So the previous paragraph's technique
for preventing label spoofing does not apply.
Rekhter & Rosen Standards Track [Page 5]
RFC 3107 Carrying Label Information in BGP-4 May 2001
It is possible though to use other techniques to avoid label spoofing
problems. If, for example, one never accepts labeled packets from
the network's "external" interfaces, and all the BGP-distributed
labels are advertised via IBGP, then there is no way for an untrusted
router to put a labeled packet into the network. One can generally
assume that one's IBGP peers (or the IBGP peers of one's Route
Reflector) will not attempt label spoofing, since they are all under
the control of a single administration.
This condition can actually be weakened significantly. One doesn't
need to refuse to accept all labeled packets from external
interfaces. One just needs to make sure that any labeled packet
received on an external interface has a top label which was actually
distributed out that interface.
Then a label spoofing problem would only exist if there are both
trusted and untrusted systems out the same interface. One way to
avoid this problem is simply to avoid this situation.
[BGP-4] Rekhter, Y. and T. Li, "A Border Gateway Protocol 4
(BGP-4)", RFC 1771, March 1995.
[BGP-CAP] Chandra, R. and J. Scudder, "Capabilities Advertisement
with BGP-4", RFC 2842, May 2000.
[BGP-MP] Bates, T., Rekhter, Y, Chandra, R. and D. Katz,
"Multiprotocol Extensions for BGP-4", RFC 2858, June
2000.
[BGP-RR] Bates, T. and R. Chandra, "BGP Route Reflection: An
alternative to full mesh IBGP", RFC 1966, June 1996.
[MPLS-ARCH] Rosen, E., Vishwanathan, A. and R. Callon,
"Multiprotocol Label Switching Architecture" RFC 3031,
January 2001.
[MPLS-ENCAPS] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y.,
Farinacci, D., Li, T. and A. Conta, "MPLS Label Stack
Encoding", RFC 3032, January 2001.
Rekhter & Rosen Standards Track [Page 6]
RFC 3107 Carrying Label Information in BGP-4 May 2001
Yakov Rekhter
Juniper Networks
1194 N. Mathilda Avenue
Sunnyvale, CA 94089
EMail: yakov@juniper.net
Eric Rosen
Cisco Systems, Inc.
250 Apollo Drive
Chelmsford, MA 01824
EMail: erosen@cisco.com
Rekhter & Rosen Standards Track [Page 7]
RFC 3107 Carrying Label Information in BGP-4 May 2001
Copyright (C) The Internet Society (2001). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Rekhter & Rosen Standards Track [Page 8]