Topology Dissemination Based on Reverse-Path Forwarding (TBRPF) is a
proactive, link-state routing protocol designed for mobile ad-hoc
networks (MANETs), which provides hop-by-hop routing along shortest
paths to each destination. Each node running TBRPF computes a source
tree (providing shortest paths to all reachable nodes) based on
partial topology information stored in its topology table, using a
modification of Dijkstra's algorithm. To minimize overhead, each
node reports only *part* of its source tree to neighbors.
TBRPF uses a combination of periodic and differential updates to keep
all neighbors informed of the reported part of its source tree. Each
node also has the option to report addition topology information (up
to the full topology), to provide improved robustness in highly
mobile networks.
TBRPF performs neighbor discovery using "differential" HELLO messages
which report only *changes* in the status of neighbors. This results
in HELLO messages that are much smaller than those of other link-
state routing protocols such as OSPF [6].
TBRPF consists of two modules: the neighbor discovery module and the
routing module (which performs topology discovery and route
computation). An overview of these modules is given in Section 5.
Ogier, et al. Experimental [Page 3]
RFC 3684 TBRPF February 2004
The keywords "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL", when
they appear in this document, are to be interpreted as described in
BCP 14, RFC 2119 [1].
This document also makes use of internal conceptual variables to
describe protocol behavior and external variables that an
implementation must allow system administrators to change. The
specific variable names, how their values change, and how their
settings influence protocol behavior are provided to demonstrate
protocol behavior. An implementation is not required to have them in
the exact form described here, so long as its external behavior is
consistent with that described in this document.
The following terms are used to describe TBRPF:
node
A router that implements TBRPF.
router ID
Each node is identified by a unique 32-bit router ID (RID), which
for IPv4 is typically equal to the IP address of one of its
interfaces. The term "node u" denotes the node whose RID is equal
to u.
interface
A node's attachment to a communication facility or medium through
which it can communicate with other nodes. A node can have
multiple interfaces. An interface can be wireless or wired, and
can be broadcast (e.g., Ethernet) or point-to-point. Each
interface is identified by its IP address. The term "interface I"
denotes the interface whose IP address is I.
link
A link is an ordered pair of interfaces (I,J) where I and J are on
two different nodes, and where interface I has recently received
packets sent from interface J. A link (i,j) from node i to node j
is said to exist if node i has an interface I and node j has an
interface J such that (I,J) is a link. Nodes i and j are called
the "tail" and "head" of the link, respectively.
bidirectional link
A link (I,J) such that interfaces I and J can both hear each
other. Also called a 2-way link.
Ogier, et al. Experimental [Page 4]
RFC 3684 TBRPF February 2004
neighbor node
A node j is said to be a neighbor of node i if node i can hear
node j on some interface. Node j is said to be a 2-way neighbor
if there is a bidirectional link between i and j.
MANET interface
Any wireless interface such that two neighbor nodes on the
interface need not be neighbors of each other. MANET nodes
typically have at least one MANET interface, but this is not a
requirement.
topology
The topology of the network is described by a graph G = (V, E),
where V is the set of nodes u and E is the set of links (u,v) in
the network.
source tree
The directed tree (denoted T) computed by each node that provides
shortest paths to all other reachable nodes.
topology update
A message that reports the state of one or more links.
parent
The parent of node i for node u is the next node on the computed
shortest path from node i to node u.
predecessor
The predecessor of a node v on the source tree is the node u such
that the link (u,v) is in the source tree.
leaf node
A leaf node of the source tree is a node on the source tree that
is not the predecessor of any other node on the source tree.
proactive routing protocol
A routing protocol in which each node maintains routes to all
reachable destinations at all times, whether or not there is
currently any need to deliver packets to those destinations. In
contrast, an "on-demand" routing protocol discovers and maintains
routes only when they are needed.
TBRPF is a proactive routing protocol designed for mobile ad-hoc
networks (MANETs). It can support networks with up to a few hundred
nodes, and can be combined with hierarchical routing techniques to
support much larger networks. Because it employs techniques to
Ogier, et al. Experimental [Page 5]
RFC 3684 TBRPF February 2004
greatly reduce control traffic, TBRPF can support much larger and
denser networks than routing protocols based on the classical link-
state algorithm (e.g., OSPF).
The number of nodes that can be supported depends on several factors,
including the MAC data rate, the rate of topology changes, and the
network density (average number of neighbors). Simulations have been
reported in which TBRPF has supported as many as 500 nodes. In
simulations with 100 nodes and 20 traffic streams (sources), using
IEEE 802.11 with a data rate of 2 Mbps, TBRPF was found to generate
approximately 80-120 kb/s of routing control traffic for the
scenarios considered, which compared favorably with other MANET
routing protocols [7][8]. A proof of correctness for TBRPF can be
found in references [8] and [9].
The TBRPF Neighbor Discovery (TND) protocol allows each node i to
quickly detect the neighbor nodes j such that a bidirectional link
(I,J) exists between an interface I of node i and an interface J of
node j. The protocol also quickly detects when a bidirectional link
breaks or becomes unidirectional.
The key feature of TND is that it uses "differential" HELLO messages
which report only *changes* in the status of links. This results in
HELLO messages that are much smaller than those of other link-state
routing protocols such as OSPF, in which each HELLO message includes
the IDs of *all* neighbors. As a result, HELLO messages can be sent
more frequently, which allows faster detection of topology changes.
TND is designed to be fully modular and independent of the routing
module. TND performs ONLY neighbor sensing, i.e., it determines
which nodes are (1-hop) neighbors. In particular, it does not
discover 2-hop neighbors (which is handled by the routing module).
As a result, TND can be used by other routing protocols, and TBRPF
can use another neighbor discovery protocol in place of TND, e.g.,
one provided by the link layer.
Nodes with multiple interfaces run TND separately on each interface,
similar to OSPF. Thus, a neighbor table is maintained for each local
interface, and a HELLO sent on a particular interface contains only
information regarding neighbors heard on that interface.
Ogier, et al. Experimental [Page 6]
RFC 3684 TBRPF February 2004
We note that, in wireless networks, it is possible for a single
interface I to receive packets from multiple interfaces J associated
with the same neighbor node. This could happen, for example, if the
neighbor uses a directional antenna with different interfaces
representing different beams. For this reason, TBRPF includes
neighbor interface addresses in HELLO messages, unlike OSPF, which
includes only router IDs in HELLO packets.
Each TBRPF node maintains a neighbor table for each local interface
I, which stores state information for each neighbor interface J heard
on that interface, i.e., for each link (I,J) between interface I and
a neighbor interface J. The status of each link can be 1-WAY, 2-WAY,
or LOST. The neighbor table for interface I determines the contents
of HELLO messages sent on interface I, and is updated based on HELLO
messages received on interface I (and possibly on link-layer
notifications).
Each TBRPF node sends (on each interface) at least one HELLO message
per HELLO_INTERVAL. Each HELLO message contains three (possibly
empty) lists of neighbor interface addresses (which are formatted as
three message subtypes): NEIGHBOR REQUEST, NEIGHBOR REPLY, and
NEIGHBOR LOST. Each HELLO message also contains the current HELLO
sequence number (HSEQ), which is incremented with each transmitted
HELLO.
In the following overview of the operation of TND, we assume that
interface I belongs to node i, and interface J belongs to node j.
When a node i changes the status of a link (I,J), it includes the
neighbor interface address J in the appropriate list (NEIGHBOR
REQUEST/REPLY/LOST) in at most NBR_HOLD_COUNT (typically 3)
consecutive HELLOs sent on interface I. This ensures that node j
will either receive one of these HELLOs on interface J, or will miss
NBR_HOLD_COUNT HELLOs and thus declare the link (J,I) to be LOST.
This technique makes it unnecessary for a node to include each 1-WAY
or 2-WAY neighbor in HELLOs indefinitely, unlike OSPF.
To avoid establishing a link that is likely to be short lived (i.e.,
to employ hysteresis), node i must receive (on interface I) at least
HELLO_ACQUIRE_COUNT (e.g., 2) of the last HELLO_ACQUIRE_WINDOW (e.g.,
3) HELLOs sent from a neighbor interface J, before declaring the link
(I,J) to be 1-WAY. When this happens, node i includes J in the
NEIGHBOR REQUEST list in each of its next NBR_HOLD_COUNT HELLO
messages sent on interface I, or until a NEIGHBOR REPLY message
containing I is received on interface I from neighbor interface J.
If node j receives (on interface J) one of the HELLOs sent from
interface I that contains J in the NEIGHBOR REQUEST list, then node j
declares the link (J,I) to be 2-WAY (unless it is already 2-WAY), and
Ogier, et al. Experimental [Page 7]
RFC 3684 TBRPF February 2004
includes I in the NEIGHBOR REPLY list in each of its next
NBR_HOLD_COUNT HELLO messages sent on interface J. Upon receiving
one of these HELLOs on interface I, node i declares the link (I,J) to
be 2-WAY.
If node i receives a HELLO on interface I, sent from neighbor
interface J, whose HSEQ indicates that at least NBR_HOLD_COUNT HELLOs
were missed, or if node i receives no HELLO on interface I sent from
interface J within NBR_HOLD_TIME seconds, then node i changes the
status of link (I,J) to LOST (unless it is already LOST), and
includes J in the NEIGHBOR LOST list in each of its next
NBR_HOLD_COUNT HELLO messages sent on interface I (unless the link
changes status before these transmissions are complete). Node j will
either receive one of these HELLOs on interface J or will miss
NBR_HOLD_COUNT HELLOs; in either case, node j will declare the link
(J,I) to be LOST. In this manner, both nodes will agree that the
link between I and J is no longer bidirectional, even if node j can
still hear HELLOs from node i.
Each node may maintain and update one or more link metrics for each
link (I,J) from a local interface I to a neighbor interface J,
representing the quality of the link. Such link metrics can be used
as additional conditions for changing the status of a neighbor, based
on the link metric going above or below some threshold. TBRPF also
allows link metrics to be advertised in topology updates, and to be
used for computing shortest paths.
Each node running TBRPF maintains a source tree, denoted T, which
provides shortest paths to all reachable nodes. Each node computes
and updates its source tree based on partial topology information
stored in its topology table, using a modification of Dijkstra's
algorithm. To minimize overhead, each node reports only part of its
source tree to neighbors. The main idea behind the current version
of TBRPF came from PTSP [10], another protocol in which each node
reports only part of its source tree. (However, TBRPF differs from
PTSP in several ways.) The current version of TBRPF should not be
confused with its previous version [11], which is a full-topology
routing protocol.
The part of T that a node reports to neighbors is called the
"reported subtree" and is denoted RT. Each node reports RT to
neighbors in *periodic* topology updates (e.g., every 5 seconds), and
reports changes (additions and deletions) to RT in more frequent
*differential* updates (e.g., every 1 second). Periodic updates
inform new neighbors of RT, and ensure that each neighbor eventually
learns RT even if it does not receive all updates. Differential
Ogier, et al. Experimental [Page 8]
RFC 3684 TBRPF February 2004
updates ensure the fast propagation of each topology update to all
nodes that are affected by the update. A received topology update is
not forwarded, but *may* result in a change to RT, which will be
reported in the next differential or periodic update. Whenever
possible, topology updates are included in the same packet as a HELLO
message, to minimize the number of control packets sent. TBRPF does
not require reliable or sequenced delivery of messages, and does not
use ACKs or NACKs.
TBRPF supports multiple interfaces, associated hosts, and network
prefixes. Information regarding associated interfaces, hosts, and
prefixes is disseminated efficiently in periodic and differential
updates, similar to the dissemination of topology updates.
The reported subtree RT consists of links (u,v) of T such that u is
in the "reported node set" RN, which is computed as follows. Node i
includes a neighbor j in RN if and only if node i determines that one
of its neighbors may select i to be its next hop on its shortest path
to j. To make this determination, node i computes the shortest
paths, up to 2 hops, from each neighbor to each other neighbor, using
only neighbors (or node i itself) as an intermediate node, and using
relay priority (included in HELLO messages) and router ID to break
ties. After a node determines which neighbors are in RN, each
reachable node u is included in RN if and only if the next hop on the
shortest path to u is in RN. A node also includes itself in RN. As
a result, the reported subtree RT includes the subtrees of T that are
rooted at neighbors in RN, and also includes all local links to
neighbors.
We note that neighbors in RN are analogous to multipoint relay (MPR)
selectors [12]. Thus, if node i selects neighbor j to be in RN, then
node i effectively selects itself to be an MPR of node j. This is
quite different from [12], in which a node does not select itself to
be an MPR, but selects a subset of its neighbors to be MPRs.
A node with a larger relay priority reports a larger part of its
source tree (on average), and is more likely to be selected as a
next-hop relay by its neighbors. A node with relay priority equal to
0 is called a non-relay node, and never forwards packets originating
from other nodes.
TBRPF does not use sequence numbers for topology updates, thus
reducing message overhead and avoiding wraparound problems. Instead,
a technique similar to SPTA [13] is used in which, for each link
(u,v) reported by one or more neighbors, only the next hop p(u) to u
is believed regarding the state of the link. (However, in SPTA each
node reports the full topology.) Using this technique, each node
maintains a topology graph TG, consisting of links that are believed
Ogier, et al. Experimental [Page 9]
RFC 3684 TBRPF February 2004
to be up, and computes T as the shortest-path tree within TG. To
allow immediate rerouting, the restriction that each link (u,v) in TG
must be reported by p(u) is relaxed temporarily if p(u) changes to a
neighbor that is not reporting the link.
Each node is required to report RT, but may report additional links,
e.g., to provide increased robustness in highly mobile networks.
More precisely, a node may maintain any subgraph H of TG that
contains T, and report the reported subgraph RH, which consists of
links (u,v) of H such that u is in RN. For example, H can equal TG,
which would provide each node with the full network topology if this
is done by all nodes. H can also be a biconnected subgraph that
contains T, which would provide each node with two disjoint paths to
each other node, if this is done by all nodes.
TBRPF allows the option to include link metrics in topology updates,
and to compute paths that are shortest with respect to the metric.
This allows packets to be sent along paths that are higher quality
than minimum-hop paths.
TBRPF allows path optimality to be traded off in order to reduce the
amount of control traffic in networks with a large diameter, where
the degree of approximation is determined by the configurable
parameter NON_TREE_PENALTY.
Nodes send TBRPF protocol data in contiguous units known as packets.
Each packet includes a header, optional header extensions, and a body
comprising one or more messages and padding options as needed. To
facilitate efficient receiver processing, senders SHOULD insert
padding options as necessary to align multi-octet words within the
TBRPF packet on natural boundaries (i.e., modulo-8/4/2 addresses for
64/32/16-bit words, respectively). Receivers MUST be capable of
processing multi-octet words whether or not aligned on natural
boundaries. The following sections specify elements of the TBRPF
packet in more detail.
TBRPF packet headers are variable-length (minimum one octet). The
format for the packet header is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vers |L|I|R|R| Reserved | Header Extensions ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Ogier, et al. Experimental [Page 10]
RFC 3684 TBRPF February 2004
Version (4 bits)
The TBRPF version number. This specification documents version 4
of the protocol.
Flags (4 bits)
Two bits (L,I) specify which header extensions (if any) follow.
Two bits (R) are reserved for future use, and MUST be zero. Any
extensions specified by these bits MUST appear in the same order
as the bits (i.e., first L, then I) as follows:
L - Length included
If the underlying delivery service provides a length field, the
sender MAY set L = '0' and omit the length extension. Otherwise,
the sender MUST set L = '1' and include a 16-bit unsigned integer
length immediately after any previous header field. The length
includes all header and data bytes and is written into the length
field in network byte order.
Receivers examine the L bit to determine whether the length field
is present. If L = '1', the receiver reads the length field to
determine the length of the TBRPF packet, including the TBRPF
packet header. Receivers discard any TBRPF packet if neither the
underlying delivery service nor the TBRPF packet header provide
packet length.
I - Router ID (RID) included
If the underlying delivery service encodes the sender's RID, the
sender MAY set I = '0' and omit the RID field. Otherwise, the
sender MUST set I = '1' and include a 4-octet RID in network byte
order immediately after any previous header fields. The RID
option provides a mechanism for implicit network-level address
resolution. A receiver that detects a RID option SHOULD create a
binding between the RID and the source address that appears in the
network-level header.
Reserved
Reserved for future use; MUST be zero.
The TBRPF packet body consists of the concatenation of one or more
TBRPF messages (and padding options where necessary). Messages and
padding options within the TBRPF packet body are encoded using the
following format:
+-+-+-+-+-+-+-+-+- - - - -
|OPTIONS| TYPE | VALUE
+-+-+-+-+-+-+-+-+- - - - -
Ogier, et al. Experimental [Page 11]
RFC 3684 TBRPF February 2004
OPTIONS (4 bits)
Four option bits that depend on TYPE.
TYPE (4 bits)
Identifier for message type or padding option.
VALUE
Variable-length field. (Format and length depend on TYPE, as
described in the following sections.)
The sequence of elements MUST be processed strictly in the order they
appear within the TBRPF packet body; a receiver must not, for
example, scan through the packet body looking for a particular type
of element prior to processing all preceding elements [2]. TBRPF
packet elements include padding options and messages as described
below.
Senders MAY insert two types of padding options where necessary,
e.g., to satisfy alignment requirements for other elements [2].
Padding options may occur anywhere within the TBRPF packet body. The
following two padding options are defined:
Pad1 option (TYPE = 0)
+-+-+-+-+-+-+-+-+
| 0 | 0 |
+-+-+-+-+-+-+-+-+
The Pad1 option inserts one octet of padding into the TBRPF packet
body; the VALUE field is omitted. If more than one octet of padding
is required, the PadN option (described next) should be used, rather
than multiple Pad1 options.
PadN option (TYPE = 1)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- - - - - - - - - - -
| 0 | 1 | LEN | Zero-valued Octets
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- - - - - - - - - - -
The PadN option inserts two or more octets of padding into the TBRPF
packet body. The first octet of the VALUE field contains an 8-bit
unsigned integer length containing a value between 0 - 253 which
specifies the number of zero-valued octets that immediately follow,
yielding a maximum total of 255 padding octets.
Ogier, et al. Experimental [Page 12]
RFC 3684 TBRPF February 2004
Additional message types are described as they occur in the following
sections. Senders encode messages as specified by the individual
message formats. Receivers detect errors in message construction,
e.g., messages with unrecognized types, messages with a non-integral
number of elements, or with fewer elements than indicated, etc. In
all cases, upon detecting an error, the receiver MUST discontinue
processing the current TBRPF packet and discard any unprocessed
elements.
This section describes the TBRPF Neighbor Discovery (TND) protocol,
which allows each node to quickly detect bidirectional links (I,J)
between a local interface I and a neighbor interface J, and to
quickly detect the loss of such links. The interface between TND and
the routing module is defined by the neighbor table maintained by TND
and the three procedures Link_Up(I,J), Link_Down(I,J), and
Link_Change(I,J), which are called by TND to announce a new link, the
loss of a link, and a change in the metric of a link, respectively.
The HELLO message has the following three subtypes:
- NEIGHBOR REQUEST (TYPE = 2)
- NEIGHBOR REPLY (TYPE = 3)
- NEIGHBOR LOST (TYPE = 4)
Each HELLO subtype has the following format:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0 | TYPE | HSEQ | Pri | n |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Neighbor Interface Address (1) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Neighbor Interface Address (2) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ... ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Neighbor Interface Address (n) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
HSEQ (8 bits)
The HELLO sequence number.
Ogier, et al. Experimental [Page 13]
RFC 3684 TBRPF February 2004
Pri (4 bits)
This field indicates the sending node's relay priority, which is
an integer between 0 and 15. A node with a higher relay priority
is more likely to be selected as the next hop on a route. The
value 0 is reserved for non-relay nodes, i.e., nodes that should
never forward packets originating from other nodes. A router in
normal operation SHOULD have a relay priority equal to 7. A
router can change its relay priority dynamically, e.g., when its
power supply becomes critical.
n (12 bits)
The number of 32-bit neighbor interface addresses in the message.
A HELLO message is the concatenation of a NEIGHBOR REQUEST message, a
NEIGHBOR REPLY message, and a NEIGHBOR LOST message, where each of
the last two messages is omitted if its list of neighbor interface
addresses is empty. Thus, a HELLO message always includes a
(possibly empty) NEIGHBOR REQUEST.
Each node maintains, for each of its local interfaces I, a neighbor
table, which stores state information for each neighbor interface J
from which HELLO messages have recently been received by interface I.
The entry for neighbor interface J, in the neighbor table for I,
contains the following variables:
nbr_rid(I,J) - The router ID of the node associated with neighbor
interface J.
nbr_status(I,J) - The current status of the link (I,J), which can
be LOST, 1-WAY, or 2-WAY.
nbr_life(I,J) - The amount of time (in seconds) remaining before
nbr_status(I,J) must be changed to LOST if no further HELLO
message from interface J is received. Set to NBR_HOLD_TIME
whenever a HELLO is received on interface I from interface J.
nbr_hseq(I,J) - The value of HSEQ in the last HELLO message
received on interface I from interface J. Used to determine the
number of HELLOs that have been missed.
nbr_count(I,J) - The remaining number of times a NEIGHBOR REQUEST/
REPLY/LOST message containing J must be sent on interface I.
hello_history(I,J) - A list of the sequence numbers of the last
HELLO_ACQUIRE_WINDOW HELLO messages received on interface I from
interface J.
Ogier, et al. Experimental [Page 14]
RFC 3684 TBRPF February 2004
nbr_metric(I,J) - An optional measure of the quality of the link
(I,J), represented by an integer between 1 and 255, where smaller
values indicate better quality. Defaults to 1 if not used.
nbr_pri(I,J) - The relay priority of the node associated with
interface J.
The entry for interface J in the neighbor table for interface I may
be deleted if no HELLO has been received on interface I from
interface J within the last 2*NBR_HOLD_TIME seconds. (It is kept
while NEIGHBOR LOST messages containing J are being transmitted.)
The absence of an entry for a given interface J is equivalent to an
entry with nbr_status(I,J) = LOST and hello_history(I,J) = NULL.
The three possible values of nbr_status(I,J) have the following
informal meanings (the exact meanings are defined by the protocol):
LOST
Interface I has not received a sufficient number of HELLO messages
recently from Interface J.
1-WAY
Interface I has received a sufficient number of HELLO messages
recently from Interface J, but the link is not 2-WAY.
2-WAY
Interfaces I and J have both received a sufficient number of HELLO
messages recently from each other.
Each node MUST send, on each local interface, at least one HELLO
message per HELLO_INTERVAL. HELLO messages MAY be sent more
frequently than this (e.g., for faster detection of topology
changes). However, to avoid the possibility that HSEQ wraps around
to the same number before a neighbor that stops receiving HELLO
messages changes the status of the link to LOST, the time between two
consecutive HELLO messages (sent on a given interface) MUST be
greater than NBR_HOLD_TIME/128 second.
To avoid synchronization of control messages, which can result in
collisions, HELLO messages SHOULD NOT be transmitted at equal
intervals. To achieve this, a node MAY choose the interval between
consecutive HELLO messages to be HELLO_INTERVAL - jitter, where
jitter is selected randomly from the interval [0, MAX_JITTER].
Ogier, et al. Experimental [Page 15]
RFC 3684 TBRPF February 2004
Each HELLO message always includes a NEIGHBOR REQUEST message, even
if its list of neighbor addresses is empty. The NEIGHBOR REQUEST
message includes the sequence number HSEQ, which is incremented by 1
(modulo 256) each time a HELLO is sent. The HELLO message also
includes a NEIGHBOR REPLY message if its list of neighbor addresses
is nonempty, and a NEIGHBOR LOST message if its list of neighbor
addresses is nonempty. The contents of these three messages are
determined by the following steps at node i for each interface I:
1. For each interface J such that nbr_status(I,J) = LOST and
nbr_count(I,J) > 0, include J in the NEIGHBOR LOST message and
decrement nbr_count(I,J).
2. For each interface J such that nbr_status(I,J) = 1-WAY and
nbr_count(I,J) > 0, include J in the NEIGHBOR REQUEST message and
decrement nbr_count(I,J).
3. For each interface J such that nbr_status(I,J) = 2-WAY and
nbr_count(I,J) > 0, include J in the NEIGHBOR REPLY message and
decrement nbr_count(I,J).
If a node restarts, so that all entries are removed from the neighbor
table, then the node MUST ensure that (for each interface) at least
one of the following two conditions is satisfied:
1. The difference between the transmission times of the first HELLO
sent after restarting and the last HELLO sent before restarting is
at least 2*NBR_HOLD_TIME.
2. Letting HSEQ_LAST denote the sequence number of the last HELLO
that was sent before restarting, the sequence number of the first
HELLO sent after restarting is set to HSEQ_LAST + NBR_HOLD_COUNT +
1 (modulo 256).
Either of these conditions ensures that, if node i with interface I
restarts, then each neighbor of node i that has a link (J,I) to
interface I will set the status of the link to LOST.
When a node receives a HELLO message, it obtains the IP address of
the sending interface from the IP header. If the TBRPF packet header
of the received HELLO contains the RID option, then the RID of the
sending node is obtained from the TBRPF packet header; otherwise it
is equal to the IP address of the sending interface. If node i (with
RID equal to i) receives a HELLO message on interface I, sent by node
j (with RID equal to j) on interface J, with sequence number HSEQ and
relay priority PRI, then node i performs the following steps:
Ogier, et al. Experimental [Page 16]
RFC 3684 TBRPF February 2004
1. If the neighbor table for interface I does not contain an entry
for interface J, create one with nbr_rid(I,J) = j, nbr_status(I,J)
= LOST (temporarily), nbr_count(I,J) = 0, and nbr_hseq(I,J) =
HSEQ.
2. Update hello_history(I,J) to reflect the received HELLO message.
If nbr_hseq(I,J) > HSEQ (due to wraparound), set nbr_hseq(I,J) =
nbr_hseq(I,J) - 256.
3. If nbr_status(I,J) = LOST and hello_history(I,J) indicates that
HELLO_ACQUIRE_COUNT of the last HELLO_ACQUIRE_WINDOW HELLO
messages from interface J have been received:
a. If interface I does not appear in the NEIGHBOR REQUEST list or
the NEIGHBOR REPLY list, set nbr_status(I,J) = 1-WAY and
nbr_count(I,J) = NBR_HOLD_COUNT.
b. Else, set nbr_status(I,J) = 2-WAY and nbr_count(I,J) =
NBR_HOLD_COUNT. Call Link_Up(I,J).
4. Else, if nbr_status(I,J) = 1-WAY:
a. If HSEQ - nbr_hseq(I,J) > NBR_HOLD_COUNT, then set
nbr_status(I,J) = LOST and nbr_count(I,J) = NBR_HOLD_COUNT.
b. Else, if interface I appears in the NEIGHBOR REQUEST list, set
nbr_status(I,J) = 2-WAY and nbr_count(I,J) = NBR_HOLD_COUNT.
Call Link_Up(I,J).
c. Else, if interface I appears in the NEIGHBOR REPLY list, set
nbr_status(I,J) = 2-WAY and nbr_count(I,J) = 0. Call
Link_Up(I,J).
5. Else, if nbr_status(I,J) = 2-WAY:
a. If interface I appears in the NEIGHBOR LOST list, set
nbr_status(I,J) = LOST and nbr_count(I,J) = 0. Call
Link_Down(I,J).
b. Else, if HSEQ - nbr_hseq(I,J) > NBR_HOLD_COUNT, set
nbr_status(I,J) = LOST and nbr_count(I,J) = NBR_HOLD_COUNT.
Call Link_Down(I,J).
c. Else, if interface I appears in the NEIGHBOR REQUEST list and
nbr_count(I,J) = 0, set nbr_count(I,J) = NBR_HOLD_COUNT.
6. Set nbr_life(I,J) = NBR_HOLD_TIME, nbr_hseq(I,J) = HSEQ, and
nbr_pri(I,J) = PRI.
Ogier, et al. Experimental [Page 17]
RFC 3684 TBRPF February 2004
Upon expiration of the timer nbr_life(I,J) in the neighbor table for
interface I, node i performs the following step:
If nbr_status(I,J) = 1-WAY or 2-WAY, set nbr_status(I,J) = LOST
and nbr_count(I,J) = NBR_HOLD_COUNT. Call Link_Down(I,J).
Some link-layer protocols (e.g., IEEE 802.11) provide a notification
that the link to a particular neighbor has failed, e.g., after
attempting a maximum number of retransmissions. If such an
notification is provided by the link layer, then node i SHOULD
perform the following step upon receipt of a link-layer failure
notification for the link (I,J) from local interface I to neighbor
interface J:
If nbr_status(I,J) = 2-WAY, set nbr_status(I,J) = LOST and
nbr_count(I,J) = NBR_HOLD_COUNT. Call Link_Down(I,J).
Each node MAY maintain and update one or more link metrics for each
link (I,J), representing the quality of the link, e.g., signal
strength, number of HELLOs received over some time interval,
reliability, stability, bandwidth, etc. Each node MUST declare a
neighbor to be LOST if either NBR_HOLD_COUNT HELLOs are missed or if
no HELLO is received within NBR_HOLD_TIME seconds; however, a node
MAY also declare a neighbor to be LOST based on a link metric being
above or below some threshold. Each node MUST receive at least
HELLO_ACQUIRE_COUNT of the last HELLO_ACQUIRE_WINDOW HELLOs from a
neighbor before declaring the neighbor 1-WAY or 2-WAY; however, a
node MAY require an additional condition based on a link metric being
above or below some threshold, before declaring the neighbor 1-WAY or
2-WAY. This document does not specify any particular link metric,
but an implementation of TBRPF that uses such metrics is considered
to be compliant with this specification.
The function Link_Change(I,J) is called to alert the routing module
whenever nbr_metric(I,J) changes significantly. If the configurable
parameter USE_METRICS is equal to 1, then the metrics nbr_metric(I,J)
are used by the routing module for route computation, as described in
Section 8.
Ogier, et al. Experimental [Page 18]
RFC 3684 TBRPF February 2004
This section lists the parameters used by the neighbor discovery
protocol, and their proposed default values. All nodes MUST be
configured to have the same value for all of the following
parameters.
Parameter Name Default Value
-------------- -------------
HELLO_INTERVAL 1 second
MAX_JITTER 0.1 second
NBR_HOLD_TIME 3 seconds
NBR_HOLD_COUNT 3
HELLO_ACQUIRE_COUNT 2
HELLO_ACQUIRE_WINDOW 3
In addition to the information required by the neighbor discovery
protocol, each node running TBRPF maintains a topology table TT,
which stores information for each known node and link in the network.
Nodes are identified by their RIDs, i.e., node u is the node whose
RID is u. The following information is stored in the topology table
at node i for each node u and link (u,v):
T(u,v) - Equal to 1 if (u,v) is in node i's source tree T, and 0
otherwise. The previous source tree is also maintained as old_T.
RN(u) - Equal to 1 if u is in node i's reported node set RN, and 0
otherwise. The previous reported node set is also maintained as
old_RN.
RT(u,v) - Equal to 1 if (u,v) is in node i's reported subtree RT,
and 0 otherwise. Since RT is defined as the set of links (u,v) in
T such that u is in RN, this variable need not be maintained
explicitly.
TG(u,v) - Equal to 1 if (u,v) is in node i's topology graph TG,
and 0 otherwise.
N - The set of 2-way neighbors of node i.
Ogier, et al. Experimental [Page 19]
RFC 3684 TBRPF February 2004
r(u,v) - The list of neighbors that are reporting link (u,v) in
their reported subtree RT. The set of links (u,v) reported by
neighbor j is denoted RT_j.
r(u) - The list of neighbors that are reporting node u in their
reported node set RN.
p(u) - The current parent for node u, equal to the next node on
the shortest path to u.
pred(u) - The node that is the predecessor of node u in the source
tree T. Equal to NULL if node u is not reachable.
pred(j,u) - The node that is the predecessor of node u in the
subtree RT_j reported by neighbor j.
d(u) - The length of the shortest path to node u. If USE_METRICS
= 0, d(u) is the number of hops to node u.
reported(u,v) - Equal to 1 if link (u,v) in TG is reported by
p(u), and 0 otherwise.
tg_expire(u) - Expiration time for links (u,v) in TG.
rt_expire(j,u) - Expiration time for links (u,v) in RT_j.
nr_expire(u,v) - Expiration time for a link (u,v) in TG such that
reported(u,v) = 0. Such non-reported links can be used
temporarily during rerouting.
metric(j,u,v) - The metric for link (u,v) reported by neighbor j.
metric(u,v) - The metric for link (u,v) in TG. For a neighbor j,
metric(i,j) is the minimum of nbr_metric(I,J) over all 2-WAY links
(I,J) from i to j.
cost(u,v) - The cost for link (u,v), equal to metric(u,v) if
USE_METRICS = 1, and otherwise equal to 1.
local_if(j) - The address of the preferred local interface for
forwarding packets to neighbor j.
nbr_if(j) - The address of the preferred interface of neighbor j.
Ogier, et al. Experimental [Page 20]
RFC 3684 TBRPF February 2004
The routing table consists of a list of tuples of the form (rt_dest,
rt_next, rt_dist, rt_if_id), where rt_dest is the destination IP
address or prefix, rt_next is the interface address of the next hop
of the route, rt_dist is the length of the route, and rt_if_id is the
ID of the local interface through which the next hop can be reached.
Each node also maintains three tables that describe associated IP
addresses or prefixes: the "interface table", which associates
interface IP addresses with router IDs, the "host table", which
associates host IP addresses with router IDs, and the "network prefix
table", which associates network prefixes with router IDs.
The "interface table" consists of tuples of the form (if_addr,
if_rid, if_expire), where if_addr is an interface IP address
associated with the router with RID = if_rid, and if_expire is the
time at which the tuple expires and MUST be removed. The interface
table at a node does NOT contain an entry in which if_addr equals the
node's own RID; thus, a node does not advertise its own RID as an
associated interface.
The "host table" consists of tuples of the form (h_addr, h_rid,
h_expire), where h_addr is a host IP address associated with the
router with RID = h_rid, and h_expire is the time at which the tuple
expires and MUST be removed.
The "network prefix table" consists of tuples of the form
(net_prefix, net_length, net_rid, net_expire), where net_prefix and
net_length describe a network prefix associated with the router with
RID = net_rid, and net_expire is the time at which the tuple expires
and MUST be removed. A MANET may be configured as a "stub" network,
in which case one or more gateway routers may announce a default
prefix such that net_prefix = net_length = 0. Two copies of each
table are kept: an "old" copy that was last reported to neighbors,
and the current copy that is updated when association messages are
received.
The TOPOLOGY UPDATE message has the two formats, depending on the
size of the message. The normal format is as follows, and is used
whenever n, NRL, and NRNL all do not exceed 255:
Ogier, et al. Experimental [Page 21]
RFC 3684 TBRPF February 2004
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|M|D|0|0| TYPE | n | NRL | NRNL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Router ID of u |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Router ID of v_1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ... ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Router ID of v_n |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| metric 1 | metric 2 | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The message body contains the n+1 router IDs for nodes u,
v_1,...,v_n, which represent the links (u,v_1),..., (u,v_n). The
first NRL of the v_k are reported leaf nodes, the next NRNL of the
v_k are reported non-leaf nodes, and the last n - (NRL+NRNL) of the
v_k are not reported (not in RN).
The M bit indicates whether or not link metrics are included in the
message. If M = 1, then a 1-octet metric is included for each of the
links (u,v_1),..., (u,v_n), following the last router ID.
The D bit indicates whether or not implicit deletion is used, and
must be set to 1 if and only if IMPLICIT_DELETION = 1.
The TOPOLOGY UPDATE message has the following three subtypes:
FULL (TYPE = 5)
A FULL update (FULL, n, NRL, NRNL, u, v_1,..., v_n) reports that
the links (u,v_1),..., (u,v_n) belong to the sending router's
reported subtree RT, and that RT contains no other links with tail
u.
ADD (TYPE = 6)
An ADD update (ADD, n, NRL, NRNL, u, v_1,..., v_n) reports that
the links (u,v_1),..., (u,v_n) have been added to the sending
router's reported subtree RT.
DELETE (TYPE = 7)
A DELETE update (DELETE, n, NRL, NRNL, u, v_1,..., v_n) reports
that the links (u,v_1),..., (u,v_n) have been deleted from the
sending router's reported subtree RT.
Ogier, et al. Experimental [Page 22]
RFC 3684 TBRPF February 2004
If n, NRL, or NRNL is larger than 255, then the long format of the
TOPOLOGY UPDATE message is used, in which the first 4 octets of the
normal format are replaced by the following 8 octets:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|M|D|1|0| TYPE | 0 | n |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NRL | NRNL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The INTERFACE ASSOCIATION (TYPE = 8) and HOST ASSOCIATION (TYPE = 9)
messages have the following format:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|ST | 0 | TYPE | Reserved | n |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Router ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IP Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IP Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The message body contains the router ID of the originating node, and
n IP addresses of interfaces (TYPE = 8) or hosts (TYPE = 9) that are
associated with the router ID. The ST field is defined below.
The NETWORK PREFIX ASSOCIATION message (TYPE = 10) has the following
format:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|ST | 0 | TYPE | Reserved | n |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Router ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PrefixLength | Prefix byte 1 | Prefix byte 2 | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... | PrefixLength | Prefix byte 1 | Prefix byte 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Ogier, et al. Experimental [Page 23]
RFC 3684 TBRPF February 2004
The message body contains the router ID of the originating node, and
n network prefixes, each specified by a 1-octet prefix length
followed immediately by the prefix, using the minimum number of whole
octets required. To minimize overhead, the prefix lengths and
prefixes are NOT aligned along word boundaries.
The INTERFACE ASSOCIATION, HOST ASSOCIATION, and NETWORK PREFIX
ASSOCIATION messages each have the following three subtypes (similar
to those for the TOPOLOGY UPDATE message):
FULL (ST = 0)
Indicates that this is a FULL update that includes all interface
addresses, host addresses, or network prefixes associated with the
given router ID.
ADD (ST = 1)
Indicates that the included IP addresses or network prefixes are
associated with the router ID, but may not include all such IP
addresses or network prefixes.
DELETE (ST = 2)
Indicates that the included IP addresses or network prefixes are
no longer associated with the router ID.
This section describes the operation of the TBRPF routing module.
The operation is divided into the following subsections: periodic
processing, updating the source tree and topology graph, updating the
routing table, updating the reported node set, generating periodic
updates, generating differential updates, processing topology
updates, expiring topology information, optional reporting of
redundant topology information, local topology changes, generating
association messages, processing association messages, and non-relay
operation. The operation is described in terms of procedures (e.g.,
Update_All), which may be executed periodically or in response to
some event, and may be called by other procedures. In all
procedures, node i is the node executing the procedure.
Each node executes the procedure Update_All() periodically, at least
once every DIFF_UPDATE_INTERVAL seconds, which is typically equal to
HELLO_INTERVAL. This procedure is defined as follows:
Ogier, et al. Experimental [Page 24]
RFC 3684 TBRPF February 2004
Update_All()
1. For each interface I, create empty message list msg_list(I).
2. For each interface I, generate a HELLO message for
interface I and add it to msg_list(I).
3. Expire_Links().
4. Update_Source_Tree().
5. Update_Routing_Table().
6. If REPORT_FULL_TREE = 0, execute Update_RN(); otherwise (the
full source tree is reported) Update_RN_Simple().
7. If current_time >= next_periodic:
7.1. Generate_Periodic_Update().
7.2. Set next_periodic = current_time + PER_UPDATE_INTERVAL.
8. Else, Generate_Diff_Update().
9. Generate_Association_Messages().
10. For each interface I, send the msg_list(I) on interface I.
11. Set old_T = T and old_RN = RN.
The procedure Update_Source_Tree() is a variant of Dijkstra's
algorithm, which is called periodically and in response to topology
changes, to update the source tree T and the topology graph TG. This
algorithm computes shortest paths subject to two link cost penalties.
The penalty NON_REPORT_PENALTY is added to the cost of links (u,v)
that are not currently reported by the parent p(u) so that, whenever
possible, a link (u,v) is included in T only if it is currently
reported by the parent. To allow immediate rerouting when p(u)
changes, it may be necessary to temporarily use a link (u,v) that is
not currently reported by the new parent. The penalty
NON_TREE_PENALTY is added to the cost of links (u,v) that are not
currently in T, to reduce the number of changes to T. When there
exist multiple paths of equal cost to a given node, router ID is used
to break ties.
The algorithm is defined as follows (where node i is the node
executing the procedure):
Update_Source_Tree()
1. For each node v in TT, set d(v) = INFINITY, pred(v) = NULL,
old_p(v) = p(v), and p(v) = NULL.
2. Set d(i) = 0, p(i) = i, pred(i) = i.
3. Set S = {i}. (S is the set of labeled nodes.)
4. For each node j in N, set d(j) = c(i,j), pred(j) = i,
and p(j) = j. (If USE_METRICS = 0, then all link costs
c(i,j) are 1.)
Ogier, et al. Experimental [Page 25]
RFC 3684 TBRPF February 2004
5. While there exists an unlabeled node u in TT such that
d(u) < INFINITY:
5.1. Let u be an unlabeled node in TT with minimum d(u).
(A heap should be used to find u efficiently.)
5.2. Add u to S (u becomes labeled).
5.3. If p(u) is not equal to old_p(u) (parent has changed):
5.3.1. For each link (u,v) in TG with tail u, if
reported(u,v) = 1, set reported(u,v) = 0 and set
nr_expire(u,v) = current_time + PER_UPDATE_INTERVAL.
5.3.2. If p(u) is in r(u) (p(u) is reporting u):
5.3.2.1. Set tg_expire(u) = rt_expire(p(u),u).
5.3.2.2. If p(u) = u (u is a neighbor), remove all links
(u,v) with tail u from TG.
5.3.2.3. For each link (u,v) with p(u) in r(u,v):
5.3.2.3.1. Add (u,v) to TG and set reported(u,v) = 1.
5.3.2.3.2. Set metric(u,v) = metric(p(u),u,v).
If USE_METRICS=1, set c(u,v)=metric(u,v).
5.4. For each node v such that (u,v) is in TG:
5.4.1. If reported(u,v) = 0,
set cost = c(u,v) + NON_REPORT_PENALTY.
(This penalizes (u,v) if not reported by p(u).)
5.4.2. Else, if p(u) = u AND u is not in r(v),
set cost = c(u,v) + NON_REPORT_PENALTY.
(This penalizes (u,v) if u is a neighbor and is not
reporting v.)
5.4.3. If (u,v) is not in old_T and p(u) != u,
set cost = cost + NON_TREE_PENALTY.
5.4.4. If (d(u) + cost, u) is lexicographically less
than (d(v), pred(v)), set d(v) = d(u) + c(u,v),
pred(v) = u, and p(v) = p(u).
6. Update the source tree T as follows:
6.1. Remove all links from T.
6.2. For each node u other than i such that pred(u) is not
NULL, add the link (pred(u), u) to T.
The routing table is updated following any change to the source tree
or the association tables (interface table, host table, or network
prefix table). The routing table is updated according to procedure
Update_Routing_Table(), which is defined as follows:
Update_Routing_Table()
1. Remove all tuples from the routing table.
Ogier, et al. Experimental [Page 26]
RFC 3684 TBRPF February 2004
2. For each node u in TT (other than this node) such that p(u) is
not NULL, add the tuple (rt_dest, rt_next, rt_dist, rt_if_id)
to the routing table, where:
rt_dest = u,
rt_if_id = local_if(p(u)),
rt_next = nbr_if(p(u)),
rt_dist = d(u).
3. For each tuple (if_addr, if_rid, if_expire) in the interface
table, if a routing table entry (rt_dest, rt_next, rt_dist,
rt_if_id) exists such that rt_dest = if_rid, add the tuple
(if_addr, rt_next, rt_dist, rt_if_id) to the routing table.
4. For each tuple (h_addr, h_rid, h_expire) in the host table, if
there exists a routing table entry (rt_dest, rt_next, rt_dist,
rt_if_id) such that rt_dest = h_rid, add the tuple (h_addr,
rt_next, rt_dist, rt_if_id) to the routing table, unless an
entry already exists with the same value for h_addr and a
lexicographically smaller value for (rt_dist, rt_dest).
5. For each tuple (net_prefix, net_length, net_rid, net_expire)
in the network prefix table, if there exists a routing table
entry (rt_dest, rt_next, rt_dist, rt_if_id) such that
rt_dest = net_rid, add the tuple (net_prefix/net_length,
rt_next, rt_dist, rt_if_id) to the routing table, unless an
entry already exists with the same value for
net_prefix/net_length and a lexicographically smaller value
for (rt_dist, rt_dest).
Recall that the reported subtree RT is defined to be the set of links
(u,v) in T such that u is in the reported node set RN. Each node
updates its RN immediately before generating periodic or differential
topology updates.
If REPORT_FULL_TREE = 1 (so that a node reports its entire source
tree), then RN simply consists of all reachable nodes, i.e., all
nodes u such that pred(u) is not NULL. The procedure that computes
RN in this manner is called Update_RN_Simple(). The rest of this
section describes how RN is computed assuming REPORT_FULL_TREE = 0.
A node first determines which of its neighbors belong to RN. Node i
includes a neighbor j in RN if and only if node i determines that one
of its neighbors may select i to be its next hop on its shortest path
to j. To make this determination, node i computes the shortest
paths, up to 2 hops, from each neighbor to each other neighbor, using
only neighbors (or node i itself) as an intermediate node, and using
Ogier, et al. Experimental [Page 27]
RFC 3684 TBRPF February 2004
relay priority and router ID to break ties. If a link metric is
used, then shortest paths are computed with respect to the link
metric; otherwise min-hop paths are computed.
After a node determines which neighbors are in RN, each node u (other
than node i) in the topology table is included in RN if and only if
the next hop p(u) to u is in RN. Equivalently, node u is included in
RN if and only if u is in the subtree of T rooted at some neighbor j
that is in RN. Thus, the reported subtree RT includes the subtrees
of T that are rooted at neighbors in RN. Node i also includes itself
in RN; thus RT also includes all local links (i,j) to neighbors j.
The precise procedure for updating RN is defined as follows:
Update_RN()
1. Set RN = empty.
2. For each neighbor s in N such that s is in r(s), i.e.,
such that s is reporting itself:
(Initialize to run Dijkstra for source s, for 2 hops.)
2.1. For each node j in N+{i}, set dist(j) = INFINITY and
par(j) = NULL.
2.2. Set dist(s) = 0 and par(s) = s.
2.3. For each node j in N+{i} such that (s,j) is in TG:
2.3.1. Set dist(j) = metric(s,j), par(j) = j.
2.3.2. For each node k in N such that (j,k) is in TG:
2.3.2.1. Set cost = metric(j,k).
2.3.2.2. If (dist(j) + cost, nbr_pri(j), j)
is lexicographically less than
(dist(k), nbr_pri(par(k)), par(k)),
set dist(k) = dist(j) + cost and par(k) = j.
2.4. For each neighbor j in N, add j to RN if par(j) = i.
3. Add i to RN. (Node i is always in RN.)
4. For each node u in the topology table, add u to RN if p(u)
is in RN.
In some cases it may be desirable to limit the radius (number of
hops) that topology information is propagated. Since each TBRPF
packet is sent only to immediate (1-hop) neighbors, this cannot be
achieved by using a time-to-live field. Instead, the propagation of
topology information can be limited to a radius of K hops by limiting
RN (at all nodes) to include only nodes that are at most K-1 hops
away. Assuming min-hop routing is used, so that d(u) is the number
of hops to node u, this can be done by modifying Step 4 of
Update_RN() as follows:
4. For each node u in the topology table, add u to RN if p(u)
is in RN and d(u) <= K-1.
Ogier, et al. Experimental [Page 28]
RFC 3684 TBRPF February 2004
Every PER_UPDATE_INTERVAL seconds, each node generates and transmits,
on all interfaces, a set of FULL TOPOLOGY UPDATE messages (one
message for each node in RN that is not a leaf of T), which describes
the reported subtree RT. Whenever possible, these messages are
included in a single packet, in order to minimize the number of
control packets transmitted.
Each topology update message contains the router IDs for n+1 nodes u,
v_1,...,v_n, which represent the n links (u,v_1),..., (u,v_n). The n
head nodes v_1,..., v_n are divided into three lists in order to
convey additional information and thus reduce the number of messages
that must be generated. In particular, the first NRL head nodes are
leaves of T, thus avoiding the need to generate separate topology
update messages for leaf nodes u. Similarly, the last n-(NRL+NRNL)
head nodes are not in RN, thus avoiding the need to generate separate
topology update messages for nodes u that have been removed from RN.
Periodic update messages are generated according to procedure
Generate_Periodic_Update(), defined as follows (where node i is the
node executing the procedure):
Generate_Periodic_Update()
For each node u in RN (including node i) that is not a leaf of T,
add the update (FULL, n, NRL, NRNL, u, v_1,..., v_n)
to msg_list(I) for each interface I, where:
(a) v_1,..., v_n are the nodes v such that (u,v) is in T,
the first NRL of these are nodes in RN that are leaves of T,
the next NRNL of these are nodes in RN that are not leaves
of T, and the last n-(NRL+NRNL) of these are not in RN.
(b) If USE_METRICS = 1, then the M (metrics) bit is set to 1 and
the link metrics metric(u,v_1),..., metric(u,v_n) are
included in the message.
Every DIFF_UPDATE_INTERVAL seconds, if it is not time to generate a
periodic update, and if RT has changed since the last time a topology
update was generated, a set of TOPOLOGY UPDATE messages describing
the changes to RT is generated and transmitted on all interfaces.
These messages are constructed according to procedure
Generate_Differential_Update(), defined as follows:
Ogier, et al. Experimental [Page 29]
RFC 3684 TBRPF February 2004
Generate_Differential_Update()
For each node u in RN:
1. If u is not in old_RN (u was added to RN) and is not a leaf
of T, add the update (FULL, n, NRL, NRNL, u, v_1,..., v_n)
to msg_list(I) for each I, where:
(a) v_1,..., v_n, NRL, and NRNL are defined as above for
periodic updates.
(b) If USE_METRICS = 1, then the M (metrics) bit is set to 1
and the link metrics metric(u,v_1),..., metric(u,v_n)
are included in the message.
2. Else, if u is in old_RN and is not a leaf of T:
2.1. Let v_1,..., v_n be the nodes v such that (u,v) is in T
AND at least one of the following 3 conditions holds:
(a) (u,v) is not in old_T, or
(b) v is in old_RN but not in RN, or
(c) v is a leaf and is in RN but not in old_RN.
2.2. If this set of nodes is nonempty, add the update
(ADD, n, NRL, NRNL, u, v_1,..., v_n) to msg_list(I) for
each interface I, where:
(a) NRL and NRNL are defined as above.
(b) If USE_METRICS = 1, then the M (metrics) bit is
set to 1 and the link metrics metric(u,v_1),...,
metric(u,v_n) are included in the message.
3. If u is in old_RN:
3.1. Let v_1,..., v_n be the nodes v such that (u,v) is in
old_T but not in TG, and either IMPLICIT_DELETION = 0
or pred(v) is not in RN (or is NULL).
(If IMPLICIT_DELETION = 1 and pred(v) is in RN, then
the deletion of (u,v) is implied by an ADD update for
another link (w,v).)
3.2. If this set of nodes is nonempty, add the update
(DELETE, n, u, v_1,..., v_n) to msg_list(I) for each I.
When a packet containing a list (msg_list) of TOPOLOGY UPDATE
messages is received from node j, the list is processed according to
the procedure Process_Updates(j, msg_list), defined as follows. In
particular, this procedure updates TT, TG, and the reporting neighbor
lists r(u) and r(u,v). If any link in T has been deleted from TG,
then Update_Source_Tree() and Update_Routing_Table() are called to
provide immediate rerouting.
Process_Updates(j, msg_list)
1. For each update = (subtype, n, NRL, NRNL, u, v_1,..., v_n)
in msg_list:
Ogier, et al. Experimental [Page 30]
RFC 3684 TBRPF February 2004
1.1. Create an entry for u in TT if it does not exist.
1.2. If subtype = FULL, Process_Full_Update(j, update).
1.3. If subtype = ADD, Process_Add_Update(j, update).
1.4. If subtype = DELETE, Process_Delete_Update(j, update).
2. If there exists any link in T that is not in TG:
2.1. Update_Source_Tree().
2.2. Update_Routing_Table().
Process_Full_Update(j, update)
1. Add j to r(u).
2. Set rt_expire(j,u) = current_time + TOP_HOLD_TIME.
3. For each link (u,v) s.t. j is in r(u,v):
3.1. Remove j from r(u,v).
3.2. If pred(j,v) = u, set pred(j,v) = NULL.
4. If j = p(u) OR p(u) = NULL:
4.1. Set tg_expire(u) = current_time + TOP_HOLD_TIME.
4.2. For each v s.t. (u,v) is in TG,
If reported(u,v) = 1, remove (u,v) from TG.
5. Process_Add_Update(j, update).
Process_Add_Update(j, update)
For m = 1,..., n:
((u,v_m) is the mth link in update.)
1. Let v = v_m.
2. Create an entry for v in TT if it does not exist.
3. Add j to r(u,v).
4. If j = p(u) OR p(u) = NULL:
4.1. Add (u,v) to TG.
4.2. Set reported(u,v) = 1.
5. If the M (metrics) bit in update is 1:
5.1. Set metric(j,u,v) to the m-th metric in the update.
5.2. If j = p(u) OR p(u) = NULL:
5.2.1. Set metric(u,v) = metric(j,u,v).
5.2.2. If USE_METRICS = 1, set c(u,v) = metric(u,v).
6. If the D (implicit deletion) bit in update is 1:
6.1. Set w = pred(j,v).
6.2. If (w != NULL AND w != u):
6.2.1. Remove j from r(w,v).
6.2.2. If j = p(w), remove (w,v) from TG.
7. Set pred(j,v) = u. (Set new predecessor.)
8. If m <= NRL (v = v_m is a reported leaf):
8.1. Set leaf_update = (FULL, 0, 0, 0, v).
8.2. Process_Full_Update(j, leaf_update).
9. If m > NRL + NRNL (v = v_m is not reported by j):
9.1. Remove j from r(v).
9.2. Set rt_expire(j,v) = 0.
9.3. For each node w s.t. j is in r(v,w),
remove j from r(v,w).
Ogier, et al. Experimental [Page 31]
RFC 3684 TBRPF February 2004
9.4. If j = p(v), then for each node w s.t. (v,w) is in TG
and reported(v,w) = 1, set reported(v,w) = 0 and set
nr_expire(v,w) = current_time + PER_UPDATE_INTERVAL.
Process_Delete_Update(j, update)
For m = 1,..., n:
((u,v_m) is the mth link in update.)
1. Let v = v_m.
2. Remove j from r(u,v).
3. If pred(j,v) = u, set pred(j,v) = NULL.
4. If j = p(u), remove (u,v) from TG.
Each node periodically checks for outdated topology information based
on the expiration timers tg_expire(u), rt_expire(j,u), and
nr_expire(u,v), and removes any expired entries from TG and from the
lists r(u) and r(u,v). This is done according to the following
procedure Expire_Links(), which is called periodically just before
the source tree is updated.
Expire_Links()
For each node u in TT other than node i:
1. If tg_expire(u) < current_time, then for each v s.t.
(u,v) is in TG, remove (u,v) from TG.
2. Else, for each v s.t. (u,v) is in TG,
if reported(u,v) = 0 AND nr_expire(u,v) < current_time,
remove (u,v) from TG.
3. For each node j in r(u), if rt_expire(j,u) < current_time:
3.1. Remove j from r(u).
3.2. For each link (u,v) s.t. j is in r(u,v),
remove j from r(u,v).
In addition, the following cleanup steps SHOULD be executed
periodically to remove unnecessary entries from the topology table
TT. A link (u,v) should be removed from TT if it is not in TG and
not in old_T. A node u should be removed from TT if all of the
following conditions hold: r(u) is empty, r(w,u) is empty for all w,
and no link of TG has u as either the head or the tail.
Each node is required to report its reported subtree RT to neighbors.
However, each node (independently of the other nodes) MAY report
additional links, e.g., to provide increased robustness in highly
mobile networks. For example, a node may compute any subgraph H of
TG that contains T, and may report the "reported subgraph" RH which
consists of links (u,v) of H such that u is in RN. In this case,
Ogier, et al. Experimental [Page 32]
RFC 3684 TBRPF February 2004
each periodic update describes RH instead of RT, and each
differential update describes changes to RH. If this option is used,
then the parameter IMPLICIT_DELETION MUST be set to 0, since the
deletion of a link cannot be implied by the addition of another link
if redundant topology information is reported.
This section describes the procedures that are followed when the
neighbor discovery module detects a new link, the loss of a link, or
a change in the metric for a link.
When a link (I,J) from a local interface I to a neighbor interface J
is discovered via the neighbor discovery module, the procedure
Link_Up(I,J) is executed, as defined below. Letting j be the
neighbor node associated with interface J, Link_Up(I,J) adds j to N
(if it does not already belong), updates the preferred local
interface local_if(j) and neighbor interface nbr_if(j) so that the
link from local_if(j) to nbr_if(j) has the minimum metric among all
links from i to j, and updates metric(i,j) to be this minimum metric.
Link_Up(I,J)
1. Let j = nbr_rid(I,J).
2. If j is not in N:
2.1. Add j to N.
2.2. Add (i,j) to TG.
2.3. Set reported(i,j) = 1.
3. If nbr_metric(I,J) < metric(i,j), set local_if(j) = I,
nbr_if(j) = J, and metric(i,j) = nbr_metric(I,J).
4. If USE_METRICS = 1, set cost(i,j) = metric(i,j).
When the loss of a link (I,J) from a local interface I to a neighbor
interface J is detected via the neighbor discovery module, the
procedure Link_Down(I,J) is executed, as defined below. Note that
routes are updated immediately when a link is lost, and if the lost
link is due to a link-layer failure notification, a differential
topology update is sent immediately.
Link_Down(I,J)
1. Let j = nbr_rid(I,J).
2. If there does not exist a link (K,L) from node i to
node j with nbr_status(K,L) = 2-WAY:
2.1. Remove j from N.
2.2. Remove (i,j) from TG.
3. If j is in N:
3.1. Let (K,L) be a link from i to j such that
nbr_metric(K,L) is the minimum metric among
all links from i to j.
Ogier, et al. Experimental [Page 33]
RFC 3684 TBRPF February 2004
3.2. Set local_if(j) = K, nbr_if(j) = L, and
metric(i,j) = nbr_metric(K,L).
3.3. If USE_METRICS = 1, set cost(i,j) = metric(i,j).
5. Update_Source_Tree().
6. Update_Routing_Table().
7. If j is not in N and lost link is due to link-layer failure
notification:
7.1. If (REPORT_FULL_TREE = 0) Update_RN().
7.2. Else, Update_RN_Simple().
7.3. Set msg_list = empty.
7.4. Generate_Diff_Update().
7.5. Send msg_list on all interfaces.
7.6. Set old_T = T and old_RN = RN.
If the metric of a link (I,J) from a local interface I to a neighbor
interface J changes via the neighbor discovery module, the following
procedure Link_Change(I,J) is executed.
Link_Change(I,J)
1. Let j = nbr_rid(I,J).
2. Let (K,L) be a link from i to j such that
nbr_metric(K,L) is the minimum metric among
all links from i to j.
3. Set local_if(j) = K, nbr_if(j) = L, and
metric(i,j) = nbr_metric(K,L).
4. If USE_METRICS = 1, set cost(i,j) = metric(i,j).
This section describes the procedures used to generate INTERFACE
ASSOCIATION, HOST ASSOCIATION, and NETWORK PREFIX ASSOCIATION
messages. Addresses or prefixes in the interface table, host table,
and network prefix table are reported to neighbors periodically every
IA_INTERVAL, HA_INTERVAL, and NPA_INTERVAL seconds, respectively. In
addition, differential changes to the tables are reported every
DIFF_UPDATE_INTERVAL seconds if it is not time for a periodic update
(similar to differential topology updates). Each node reports only
addresses or prefixes that are associated with nodes in the reported
node set RN; this ensures the efficient broadcast of all associated
addresses and prefixes to all nodes in the network.
The generated messages are sent on each interface. Whenever
possible, these messages are combined into the same packet, in order
to minimize the number of control packets transmitted.
Generate_Association_Messages()
1. Generate_Interface_Association_Messages().
2. Generate_Host_Association_Messages().
Ogier, et al. Experimental [Page 34]
RFC 3684 TBRPF February 2004
3. Generate_Network_Prefix_Association_Messages().
Generate_Interface_Association_Messages()
1. If current_time > next_ia_time:
1.1. Set next_ia_time = current_time + IA_INTERVAL.
1.2. For each node u in RN:
1.2.1. Let addr_1,..., addr_n be the interface IP
addresses associated with RID u in the current
interface table.
1.2.2. If this list is nonempty, add the INTERFACE
ASSOCIATION message (FULL, n, u, addr_1,..., addr_n)
to msg_list(I) for each I.
2. Else, for each node u in RN:
2.1. Add the INTERFACE ASSOCIATION message (ADD, n, u,
addr_1,..., addr_n) to msg_list(I) for each I, where
addr_1,..., addr_n are the interface IP addresses that
are associated with RID u in the current interface table
but not in the old interface table.
2.2. Add the INTERFACE ASSOCIATION message (DELETE, n, u,
addr_1,..., addr_n) to msg_list(I) for each I, where
addr_1,..., addr_n are the interface IP addresses that
are associated with RID u in the old interface table
but not in the current interface table.
Generate_Host_Association_Messages()
1. If current_time > next_ha_time:
1.1. Set next_ha_time = current_time + HA_INTERVAL.
1.2. For each node u in RN:
1.2.1. Let addr_1,..., addr_n be the host IP addresses
associated with RID u in the current host table.
1.2.2. If this list is nonempty, add the HOST ASSOCIATION
message (FULL, n, u, addr_1,..., addr_n) to
msg_list(I) for each I.
2. Else, for each node u in RN:
2.1. Add the HOST ASSOCIATION message (ADD, n, u,
addr_1,..., addr_n) to msg_list(I) for each I, where
addr_1,..., addr_n are the host IP addresses that
are associated with RID u in the current host table
but not in the old host table.
2.2. Add the HOST ASSOCIATION message (DELETE, n, u,
addr_1,..., addr_n) to msg_list(I) for each I, where
addr_1,..., addr_n are the host IP addresses that
are associated with RID u in the old host table
but not in the current host table.
Ogier, et al. Experimental [Page 35]
RFC 3684 TBRPF February 2004
Generate_Network_Prefix_Association_Messages()
1. If current_time > next_npa_time:
1.1. Set next_npa_time = current_time + NPA_INTERVAL.
1.2. For each node u in RN:
1.2.1. Let length_1, prefix_1,..., length_n, prefix_n
be the network prefix lengths and prefixes associated
with RID u in the current network prefix table.
1.2.2. If this list is nonempty, add the NETWORK PREFIX
ASSOCIATION message (FULL, n, u, length_1, prefix_1,
..., length_n, prefix_n) to msg_list(I) for each I.
2. Else, for each node u in RN:
2.1. Add the NETWORK PREFIX ASSOCIATION message
(ADD, n, u, prefix_1,..., prefix_n) to msg_list(I) for
each I, where prefix_1,..., prefix_n are the network
prefixes that are associated with RID u in the current
prefix table but not in the old prefix table.
2.1. Add the NETWORK PREFIX ASSOCIATION message
(DELETE, n, u, prefix_1,..., prefix_n) to msg_list(I) for
each I, where prefix_1,..., prefix_n are the network
prefixes that are associated with RID u in the old prefix
table but not in the current prefix table.
When an INTERFACE ASSOCIATION, HOST ASSOCIATION, or NETWORK PREFIX
ASSOCIATION message is received from node j, the interface table,
host table, or network prefix table, respectively, is updated as
described in the following three procedures.
Process_Interface_Association_Messages(j, msg_list)
For each message (subtype, n, u, addr_1,..., addr_n) in msg_list
such that j = p(u):
1. If subtype = FULL, remove all entries with if_rid = u
from the interface table.
2. If subtype = FULL or ADD, then for m = 1,..., n,
add the tuple (if_addr, if_rid, if_expire) to the
interface table, where:
if_addr = addr_m,
if_rid = u,
if_expire = current_time + IA_HOLD_TIME.
3. If subtype = DELETE, then for m = 1,..., n,
remove the tuple (if_addr, if_rid, if_expire) from the
interface table, where if_addr = addr_m and if_rid = u.
Ogier, et al. Experimental [Page 36]
RFC 3684 TBRPF February 2004
Process_Host_Association_Messages(j, msg_list)
For each message (subtype, n, u, addr_1,..., addr_n) in msg_list
such that j = p(u):
1. If subtype = FULL, remove all entries with h_rid = u
from the host table.
2. If subtype = FULL or ADD, then for m = 1,..., n,
add the tuple (h_addr, h_rid, h_expire) to the
host table, where:
h_addr = addr_m,
h_rid = u,
h_expire = current_time + HA_HOLD_TIME.
3. If subtype = DELETE, then for m = 1,..., n,
remove the tuple (h_addr, h_rid, h_expire) from the
host table, where h_addr = addr_m and h_rid = u.
Process_Network_Prefix_Association_Messages(j, msg_list)
For each message (subtype, n, u, length_1, prefix_1, ...,
length_n, prefix_n) in msg_list such that j = p(u):
1. If subtype = FULL, remove all entries with net_rid = u
from the prefix table.
2. If subtype = FULL or ADD, then for m = 1,..., n,
add the tuple (net_prefix, net_length, net_rid,
net_expire) to the network prefix table, where:
net_prefix = prefix_m,
net_length = length_m,
net_rid = u,
net_expire = current_time + NPA_HOLD_TIME.
3. If subtype = DELETE, then for m = 1,..., n,
remove the tuple (net_prefix, net_length, net_rid,
net_expire) from the network prefix table, where
net_prefix = prefix_m, net_length = length_m,
and net_rid = u.
Nodes with relay priority equal to zero are called non-relay nodes,
and do not forward packets (of any type) that are received from other
nodes. A non-relay node is implemented simply by not generating or
transmitting any TOPOLOGY UPDATE messages. A non-relay node may
report (in association messages) addresses or prefixes that are
associated with itself, but not those associated with other nodes.
HELLO messages must be transmitted in order to establish links with
neighbor nodes. The following procedures can be omitted in non-relay
nodes: Update_RN(), Generate_Periodic_Update(), and
Generate_Diff_Update().
Ogier, et al. Experimental [Page 37]
RFC 3684 TBRPF February 2004
This section lists the configurable parameters used by the routing
module, and their proposed default values. All nodes MUST have the
same value for all of the following parameters except
REPORT_FULL_TREE and IMPLICIT_DELETION.
Parameter Name Default Value
-------------- -------------
DIFF_UPDATE_INTERVAL 1 second
PER_UPDATE_INTERVAL 5 seconds
TOP_HOLD_TIME 15 seconds
NON_REPORT_PENALTY 1.01
NON_TREE_PENALTY 0.01
IA_INTERVAL 10 seconds
IA_HOLD_TIME 3 * IA_INTERVAL
HA_INTERVAL 10 seconds
HA_HOLD_TIME 3 * HA_INTERVAL
NPA_INTERVAL 10 seconds
NPA_HOLD_TIME 3 * NPA_INTERVAL
USE_METRICS 0
REPORT_FULL_TREE 0
IMPLICIT_DELETION 1
This section describes a mechanism for the efficient best-effort
flooding (or network-wide broadcast) of packets to all nodes of a
connected ad-hoc network. This mechanism can be considered an
optimization of the classical flooding algorithm in which each packet
is transmitted by every node of the network. In TBRPF flooding,
information provided by TBRPF is used to decide whether a given
received flooded packet should be forwarded. As a result, each
packet is transmitted by only a relatively small subset of nodes,
thus consuming much less bandwidth than classical flooding.
This document specifies that the flooding mechanism use the IPv4
multicast address 224.0.1.20 (currently assigned by IANA for "any
private experiment"). Every node maintains a duplicate cache to keep
track of which flooded packets have already been received. The
duplicate cache contains, for each received flooded packet, the
flooded packet identifier (FPI), which for IPv4 is composed of the
source IP address, the IP identification, and the fragment offset
values obtained from the IP header [14].
When a node receives a packet whose destination IP address is the
flooding address (224.0.1.20), it checks its duplicate cache for an
entry that matches the packet. If such an entry exists, the node
Ogier, et al. Experimental [Page 38]
RFC 3684 TBRPF February 2004
silently discards the flooded packet since it has already been
received. Otherwise, the node retransmits the packet on all
interfaces (see the exception below) if and only if the following
conditions hold:
1. The TBRPF node associated with the source IP address of the packet
belongs to the set RN of reported nodes computed by TBRPF.
2. When decremented, the 'ip_ttl' in the IPv4 packet header
(respectively, the 'hop_count' in the IPv6 packet header) is
greater than zero.
If the packet is to be retransmitted, it is sent after a small random
time interval in order to avoid collisions. If the interface on
which the packet was received is not a MANET interface (see the
Terminology section), then the packet should not be retransmitted on
that interface.
TBRPF is particularly well suited to MANETs consisting of mobile
nodes with wireless network interfaces operating in peer-to-peer
fashion over a multiple access communications channel. Although
applicable across a much broader field of use, TBRPF is particularly
well suited for supporting the standard DARPA Internet protocols
[3][2]. In the following sections, we discuss practical
considerations for the operation of TBRPF on MANETs.
We assume a MANET data link layer that supports broadcast, multicast
and unicast addressing with best-effort (not guaranteed) delivery
services between neighbors (i.e., a pair of nodes within operational
communications range of one another). We further assume that each
interface belonging to a node in the MANET is assigned a unicast data
link layer address that is unique within the MANET's scope. While
such uniqueness is not strictly guaranteed, the assumption of
uniqueness is consistent with current practices for deployment of the
Internet protocols on specific link layers. Methods for duplicate
link layer address detection and deconfliction are beyond the scope
of this document.
MANETs are formed as collections of routers and non-routing nodes
that use network layer addresses when calculating the MANET topology.
We assume that each node has at least one data link layer interface
(described above) and that each such interface is assigned a network
Ogier, et al. Experimental [Page 39]
RFC 3684 TBRPF February 2004
layer address that is unique within the MANET. (Methods for network
layer address assignment and duplicate address detection are beyond
the scope of this document.) We further assume that each node will
select a unique Router ID (RID) for use in TBRPF protocol messages,
whether or not the node acts as a MANET router. Finally, we assume
that each MANET router supports the multi-hop relay paradigm at the
network layer; i.e., each router provides an inter-node forwarding
service via network layer host routes which reflect the current MANET
topology as perceived by TBRPF.
TBRPF employs a proactive neighbor discovery protocol at the network
layer that maintains bi-directional link state for neighboring nodes
through the periodic transmission of messages. Since TBRPF neighbor
discovery messages contain both the data link and network layer
address of the sender, implementations MAY perform automatic
network-to-data link layer address resolution for the nodes with
which they form links. An implementation may use such a mechanism to
avoid additional message overhead and potential for packet loss
associated with on-demand address resolution mechanisms such as ARP
[15] or IPv6 Neighbor Discovery [16]. Implementations MUST respond
to on-demand address resolution requests in the normal manner.
MANET nodes may comprise multiple interfaces; each with a unique
network layer address. Additionally, MANET nodes may wish to publish
alias addresses such as when multiple network layer addresses are
assigned to the same interface or when the MANET node is serving as a
Mobile IP [17] home agent. Multiple interfaces and alias addresses
are advertised in INTERFACE ASSOCIATION messages, which bind each
such address to the node's RID.
MANET routers may advertise network prefixes which the router
discovered via attached networks, external routes advertised by other
protocols, or other means. Network prefixes are advertised in
NETWORK PREFIX ASSOCIATION messages, which bind each such prefix to
the node's RID.
Non-MANET hosts may establish connections to MANET routers through
on-demand mechanisms such as ARP or IPv6 Neighbor Discovery. Such
connections do not constitute a MANET link and therefore are not
reported in TBRPF topology updates. Non-MANET hosts are advertised
Ogier, et al. Experimental [Page 40]
RFC 3684 TBRPF February 2004
in HOST ASSOCIATION messages, which bind the IP address of each host
to the node's RID.
TBRPF packets are communicated using UDP/IP. Port 712 has been
assigned by IANA for exclusive use by TBRPF. Implementations in
private networks MAY employ alternate data delivery services (i.e.,
raw IP or local data-link encapsulation). The selection of an
alternate data delivery service MUST be consistent among all MANET
routers in the private network. In all implementations, the data
delivery service MUST provide a checksum facility.
The following sections specify the operation of TBRPF over UDP/IP.
When IPv4 is used, TBRPF nodes obey IPv4 host and router requirements
[4][5]. TBRPF packets are sent to the multicast address 224.0.0.2
(All Routers) and thus reach all TBRPF routers within single-hop
transmission range of the sender. TBRPF routers MUST NOT forward
packets sent to this multicast address.
Since non-negligible packet loss due to link failure, interference,
etc. can occur, implementations SHOULD avoid IPv4 fragmentation/
reassembly whenever possible, by splitting large TBRPF protocol
packets into multiple smaller packets at the application layer. When
fragmentation is unavoidable, senders SHOULD NOT send TBRPF packets
that exceed the minimum reassembly buffer size ([4], section 3.3.2)
for all receivers in the network.
The specification of TBRPF for IPv6 is the same as for IPv4, except
that 32-bit IPv4 addresses are replaced by 128-bit IPv6 addresses.
However, to minimize overhead, router IDs remain at 32 bits, similar
to OSPF for IPv6 [18].
The IANA has assigned port number 712 for TBRPF.
The TBRPF flooding mechanism specified in this document uses the IPv4
multicast address 224.0.1.20, which is currently assigned by IANA for
"any private experiment". In the event that this specification is
advanced to standards track, a new multicast address assignment would
be requested for this purpose.
Ogier, et al. Experimental [Page 41]
RFC 3684 TBRPF February 2004
Wireless networks are vulnerable to a variety of attacks, including
denial-of-service attacks (e.g., flooding and jamming), man-in-the-
middle attacks (e.g., interception, insertion, deletion,
modification, replaying) and service theft. To counter such attacks,
it is important to prevent the spoofing (impersonation) of TBRPF
nodes, and to prevent unauthorized nodes from joining the network via
neighbor discovery. To achieve this, TBRPF packets can be
authenticated using the IP Authentication Header [19][20]. In
addition, the Encapsulating Security Payload (ESP) header [21] can be
used to provide confidentiality (encryption) of TBRPF packets.
The IETF SEcuring Neighbor Discovery (SEND) Working Group analyzes
trust models and threats for ad hoc networks [22]. TBRPF can be
extended in a straightforward manner to use SEND mechanisms, e.g.,
[23].
The authors would like to thank the Army Systems Engineering Office
(ASEO) for funding part of this work.
The authors would like to thank several members of the MANET working
group for many helpful comments and suggestions, including Thomas
Clausen, Philippe Jacquet, and Joe Macker.
The authors would like to thank Bhargav Bellur for major
contributions to the original (full-topology) version of TBRPF,
Ambatipudi Sastry for his support and advice, and Julie S. Wong for
developing a new implementation of TBRPF and suggesting several
clarifications to the TBRPF Routing Operation section.
[1] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
[2] Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6)
Specification", RFC 2460, December 1998.
[3] Postel, J., "Internet Protocol", STD 5, RFC 791, September 1981.
[4] Braden, R., Ed., "Requirements for Internet Hosts -
Communication Layers", STD 3, RFC 1122, October 1989.
Ogier, et al. Experimental [Page 42]
RFC 3684 TBRPF February 2004
[5] Baker, F., Ed., "Requirements for IP Version 4 Routers", RFC
1812, June 1995.
[6] Moy, J., "OSPF Version 2", STD 54, RFC 2328, April 1998.
[7] Ogier, R., Message in IETF email archive for MANET,
ftp://ftp.ietf.org/ietf-mail-archive/manet/2002-02.mail,
February 2002.
[8] Ogier, R., "Topology Dissemination Based on Reverse-Path
Forwarding (TBRPF): Correctness and Simulation Evaluation",
Technical Report, SRI International, October 2003.
[9] Ogier, R., Message in IETF email archive for MANET,
ftp://ftp.ietf.org/ietf-mail-archive/manet/2002-03.mail, March
2002.
[10] Ogier, R., "Efficient Routing Protocols for Packet-Radio
Networks Based on Tree Sharing", Proc. Sixth IEEE Intl. Workshop
on Mobile Multimedia Communications (MOMUC'99), November 1999.
[11] Bellur, B. and R. Ogier, "A Reliable, Efficient Topology
Broadcast Protocol for Dynamic Networks", Proc. IEEE INFOCOM
'99, New York", March 1999.
[12] Clausen, T. and P. Jacquet, Eds., "Optimized Link State Routing
Protocol (OLSR)", RFC 3626, October 2003.
[13] Bertsekas, D. and R. Gallager, "Data Networks", Prentice-Hall,
1987.
[14] Perkins, C., Belding-Royer, E. and S. Das, "IP Flooding in Ad
Hoc Mobile Networks", Work in Progress, November 2001.
[15] Plummer, D., "Ethernet Address Resolution Protocol: Or
converting network protocol addresses to 48.bit Ethernet address
for transmission on Ethernet hardware", STD 37, RFC 826,
November 1982.
[16] Narten, T., Nordmark, E. and W. Simpson, "Neighbor Discovery for
IP Version 6 (IPv6)", RFC 2461, December 1998.
[17] Perkins, C., Ed., "IP Mobility Support for IPv4", RFC 3344,
August 2002.
Ogier, et al. Experimental [Page 43]
RFC 3684 TBRPF February 2004
[18] Coltun, R., Ferguson, D. and J. Moy, "OSPF for IPv6", RFC 2740,
December 1999.
[19] Kent, S. and R. Atkinson, "Security Architecture for the
Internet Protocol", RFC 2401, November 1998.
[20] Kent, S. and R. Atkinson, "IP Authentication Header", RFC 2402,
November 1998.
[21] Kent, S. and R. Atkinson, "IP Encapsulating Security Payload
(ESP)", RFC 2406, November 1998.
[22] Nikander, P., "IPv6 Neighbor Discovery Trust Models and
Threats", Work in Progress, April 2003.
[23] Arkko, J., "SEcure Neighbor Discovery (SEND)", Work in Progress,
June 2003.
Ogier, et al. Experimental [Page 44]
RFC 3684 TBRPF February 2004
Authors' Addresses
Richard G. Ogier
SRI International
333 Ravenswood Ave.
Menlo Park, CA 94025
USA
Phone: +1 650 859-4216
Fax: +1 650 859-4812
EMail: ogier@erg.sri.com
Fred L. Templin
Nokia
313 Fairchild Drive
Mountain View, CA 94043
USA
Phone: +1 650 625 2331
Fax: +1 650 625 2502
EMail: ftemplin@iprg.nokia.com
Mark G. Lewis
SRI International
333 Ravenswood Ave.
Menlo Park, CA 94025
USA
Phone: +1 650 859-4302
Fax: +1 650 859-4812
EMail: lewis@erg.sri.com
Ogier, et al. Experimental [Page 45]
RFC 3684 TBRPF February 2004
Full Copyright Statement
Copyright (C) The Internet Society (2004). This document is subject
to the rights, licenses and restrictions contained in BCP 78 and
except as set forth therein, the authors retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE
REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE
INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed
to pertain to the implementation or use of the technology
described in this document or the extent to which any license
under such rights might or might not be available; nor does it
represent that it has made any independent effort to identify any
such rights. Information on the procedures with respect to
rights in RFC documents can be found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use
of such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository
at http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention
any copyrights, patents or patent applications, or other
proprietary rights that may cover technology that may be required
to implement this standard. Please address the information to the
IETF at ietf-ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Ogier, et al. Experimental [Page 46]