Cisco Guard and Traffic Anomaly Detector Hardware Installation and Configuration Note

Product names: Cisco Guard XT 5650 and Cisco Traffic Anomaly Detector XT 5600

Product numbers: AGXT-5650-GET-A-K9, AGXT-5650-MMF-A-K9, ADXT-5600-GET-A-K9, ADXT-5600-MMF-A-K9

This document describes how to install the Cisco Guard (Guard) and the Traffic Anomaly Detector (Detector). This document refers to both the Guard and the Detector as the "appliance."

The Cisco Guard is a distributed denial-of-service (DDoS) mitigation product that receives traffic diverted from attacked targets, cleans this traffic, and forwards the cleaned traffic to its original path.

The Cisco Traffic Anomaly Detector is a distributed denial-of-service (DDoS) detection product that receives a copy of the traffic that is destined to the target, analyzes that traffic, and sends out an alert when it detects a DDoS attack. The Detector can also activate a configured Guard to mitigate these attacks.

Safety Overview

Safety warnings appear throughout this publication in procedures that, if performed incorrectly, may harm you. A warning symbol precedes each warning statement.

Parts List

Required Tools and Equipment

Installation Guidelines

Safety Guidelines

This section provides safety information for installing the appliance and contains the following topics:

Read the installation instructions in this document before you connect the system to its power source. Failure to read and follow these guidelines could lead to an unsuccessful installation and possibly damage the system and components.

You should observe the following safety guidelines when working with any equipment that connects to electrical power or telephone wiring. They can help you avoid injuring yourself or damaging the appliance.

The following warnings and cautions are provided to help you prevent injury to yourself or damage to the devices:

Warning	IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071 SAVE THESE INSTRUCTIONS

Warning Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord. Statement 1

Warning Read the installation instructions before you connect the system to its power source. Statement 10

Warning This unit might have more than one power cord. To reduce the risk of electric shock, disconnect the two power supply cords before servicing the unit. Statement 14

Warning The ports labeled "Ethernet," "10BaseT," "Token Ring," "Console," and "AUX" are safety extra-low voltage (SELV) circuits. SELV circuits should only be connected to other SELV circuits. Because the BRI circuits are treated like telephone-network voltage, avoid connecting the SELV circuit to the telephone network voltage (TNV) circuits. Statement 22

Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals. Statement 43

Warning The safety cover is an integral part of the product. Do not operate the unit without the safety cover installed. Operating the unit without the cover in place will invalidate the safety approvals and pose a risk of fire and electrical hazards. Statement 117

Warning Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 213

Warning Before working on a chassis or working near power supplies, unplug the power cord on AC units. Statement 246

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001

Warning	To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: •This unit should be mounted at the bottom of the rack if it is the only unit in the rack. •When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. •If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Statement 1006

Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Statement 1015

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

Warning Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network voltages. Statement 1041

Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045

Warning This equipment is intended to be grounded to comply with emission and immunity requirements. Ensure that the switch functional ground lug is connected to earth ground during normal use. Statement 1064

Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074

General Precautions

•

Keep all system components away from radiators and heat sources, and do not block cooling vents.

•

Do not spill food or liquids on your system components, and never operate the product in a wet environment. If the computer gets wet, see the appropriate chapter in your troubleshooting guide or contact the Cisco Technical Assistance Center. For instructions on contacting the Technical Assistance Center, see Obtaining Technical Assistance.

•

Do not push any objects into the openings of your system components. Doing so can cause fire or electric shock by shorting out interior components.

•

Position system cables and power cables carefully; Be sure to route the system cables and the power cable and plug so that they cannot be stepped on or tripped over. Be sure that nothing rests on your system component cables or power cable.

•

Do not modify power cables or plugs. Consult a licensed electrician or your power company for site modifications. Always follow your local/national wiring rules.

•

To help avoid possible damage to the system board, wait 5 seconds after turning off the system before removing a component from the system board or before disconnecting a peripheral device from the computer.

Maintaining Safety with Electricity

•

If any of the following conditions occur contact the Cisco Technical Assistance Center:

–

The appliance does not operate correctly when you follow the operating instructions.

•

Use the correct external power source. Operate the appliance only from the type of power source indicated on the electrical ratings label. If you are not sure of the type of power source required, consult the Cisco Technical Assistance Center or a local power company.

•

Use only approved power cables. An approved power cable arrived with your appliance and is intended for use with your system (approved for use in your country, based on the shipping location). If you must purchase an additional power cable, ensure that it is rated for the appliance and for the voltage and the specific current that are marked on the appliance's electrical ratings label. The voltage and current rating for the cable should be greater than the ratings that are marked on the appliance.

•

To prevent electric shock, plug the appliance components and peripheral power cables into properly grounded electrical outlets. These cables are equipped with three-prong plugs to ensure proper grounding. Do not use adapter plugs or remove the grounding prong from a cable.

•

To protect your system and components from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptable power supply (UPS).

•

Do not modify power cables or plugs. Consult a licensed electrician or your power company for site modifications. Always follow your local and national wiring rules.

Protecting Against Electrostatic Discharge

Static electricity can harm the delicate components inside of your computer. To prevent static damage, discharge static electricity from your body before you touch any electronic components on your computer, such as the microprocessor. You can do so by touching an unpainted metal surface on the computer chassis.

As you continue to work inside the computer, periodically touch an unpainted metal surface to remove any static charge your body may have accumulated.

You can also take the following steps to prevent damage from electrostatic discharge (ESD):

•

When unpacking a static-sensitive component from its shipping carton, do not remove the component from the antistatic packing material until you are ready to install the component in your computer. Just before unwrapping the antistatic packaging, be sure to discharge static electricity from your body.

•

When transporting a sensitive component, first place it in an antistatic container or packaging.

•

Handle all sensitive components in a static-safe area. If possible, use antistatic floor pads and workbench pads.

Preventing EMI

When you run wires for any significant distance in an electromagnetic field, electromagnetic interference (EMI) can occur between the field and the signals on the wires.

Strong EMI, especially when it is caused by lightning or radio transmitters, can destroy the signal drivers and receivers in the system and can create an electrical hazard by conducting power surges through lines and into the system.

Be aware that improper plant wiring can result in radio frequency interference (RFI).

Preparing Your Site for Installation

This section describes the site requirements for safe installation and operation of your appliance. Ensure that your site is properly prepared before beginning installation.

Environmental

When planning your site layout and equipment locations, follow the precautions described in this section to help avoid equipment failures and reduce the possibility of environmentally caused shutdowns. If you experience shutdowns or unusually high errors with your existing equipment, these precautions will help you to isolate the cause of the failures and prevent future problems.

Use the following precautions when planning the operating environment for your appliance:

•

Always follow the ESD-prevention procedures described in Preventing EMI, to avoid damage to the appliance. Damage from static discharge can cause immediate or intermittent equipment failure.

•

Make sure that the chassis cover is secure. An open chassis allows air leaks, which could interrupt and redirect the flow of cooling air from internal components.

•

Electrical equipment generates heat. Ambient air temperature might not be adequate to cool equipment to acceptable operating temperatures without adequate circulation. Make sure that the room in which you operate has adequate air circulation.

•

Install the appliance in a restricted access area, where access can be gained only by service personnel through the use of a special tool, lock and key, or other means of security.

•

Choose a site that maintains an ambient temperature of 10� to 35�C (50� to 95�F).

•

Keep tools and chassis components off of the floor and away from foot traffic.

•

Clear the area of possible hazards, such as moist floors, ungrounded power extension cables, and missing safety grounds.

•

Keep the area around the chassis free from dust and foreign conductive material (such as metal flakes from nearby construction activity).

AC Power

Ensure that the plug-socket combination is accessible at all times because it serves as the main disconnecting device. For the Guard and the Detector power requirements, see Connecting the Appliance.

Cabling

Use the cables in the accessory kit to connect the appliance console port to a console or computer that is running a console program. In addition to using the console cable, use the provided standard Ethernet cable to connect the appliance to your network.

Precautions for Rack-Mounting

Observe the following precautions for rack stability and safety. Also, for specific warning and caution statements and procedures, refer to the rack installation documentation that accompanied the rack.

Note The term "component" refers to any server, storage system, or appliance, and to various peripherals or supporting hardware.

•

Do not move large racks by yourself. Due to the height and weight of the rack, a minimum of two people are needed to accomplish this task.

•

Ensure that the rack is level and stable before extending a component from the rack.

•

Do not overload the AC supply branch circuit that provides power to the rack. The total rack load should not exceed 80 percent of the branch circuit rating.

•

Do not step on or stand on any system or component when servicing other systems and components in a rack.

•

This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

•

When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.

•

If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.

Front Panel Description

Rear Panel Description

Table 1 Front Panel Items
No	Item	Description
1	System LED	Indicates whether or not the appliance is receiving power and functioning properly. The system LED can have the following status: •Green—The appliance is in normal operation. •Blinking—The appliance is receiving power but is not powered up. •Off—The appliance in not connected to a power source, or the power supply or the LED failed.
2	Power control button	Turns the appliance on or off.
3	Reset button	Resets the appliance and runs the power-on self test. You may need to use a pen or the end of a straightened paperclip to press the button.
4	CD-ROM drive	Reads information from a CD-ROM.
5	Diskette drive	Reads information from a diskette.
6	Hard disk drive	Stores computer data.

Table 2 Rear Panel Items
No	Item	Description
1	Console serial socket	RS-232 port. Use this port to attach a console.
2	Monitor cable socket	Console monitor connector.
3	Keyboard cable socket	Console keyboard connector.
4	Mouse cable socket	Console mouse connector.
5	Eth0 socket	10/100/1000 BASE-T ethernet network interface socket. Use this port to connect out-of-band management.
6	Eth1 socket	10/100/1000 BASE-T ethernet network interface socket. Use this port to connect out-of-band management.
7	USB socket	USB port. Use this port to connect the mini-USB cable to the hardware diagnostics card. Caution You must connect the mini-USB cable before you power up the appliance.
8	Accelerator card	Cisco proprietary accelerator card.
9	Giga1 socket	Network interface socket. The socket may be copper or fiber. See Table 3 for more information. Use this socket to connect the appliance to the network.
10	Giga0 socket	Network interface socket. The socket may be copper or fiber. See Table 3 for more information. Use this socket to connect the appliance to the network.
11	Accelerator card serial socket	Accelerator card serial socket. Note Do not use this port. This port is intended for use by Cisco TAC personnel only.
12	USB socket on hardware diagnostics card	USB port. Use this port to connect the mini-USB cable.
13	Hardware diagnostics card	Hardware diagnostic card.
14	Power Cable Socket	AC power receptacle. Use this port to connect the appliance to an AC power source.
15	Power Cable Socket	AC power receptacle. Use this port to connect the appliance to an AC power source.

Warning The Cisco proprietary accelerator card contains a CLASS I LASER product. This module satisfies Class I Laser Safety requirements in accordance with the US FDA/CDRH and international IEC-825 standards.

Connecting the Appliance

This section describes how to connect the appliance to the network and power sources, and contains it the following topics:

Connecting the Mini-USB Cable

Step 1

Connect the small plug on the mini-USB cable to the USB socket on the hardware diagnostics card. (See item 12 in Figure 2.)

Step 2

Connect the other plug to either of the USB ports on the chassis. (See item 7 in Figure 2.)

Connecting the Appliance to Your Network

Step 1

Connect the in-band cable (copper or fiber) to the in-band network socket. (See items 9 and 10 in Figure 2.)

Step 2

Connect the other end of the in-band cable (copper or fiber) to a hub, switch, or router in your network.

Note Ensure that you connect the Detector to a port-mirroring switch or to an optical splitter.

Step 3

Connect the Ethernet 10/100/1000BASE-T cable to the network socket of the appliance. (See items 5 and 6 in Figure 2.)

Step 4

Connect the other end of the Ethernet 10/100/1000BASE-T to your management network socket.

Connecting AC Power

Step 2

Plug the AC power cord into a power cable receptacle at the rear of the appliance. (See item 15 in Figure 2.)

Step 4

Plug the AC power cord into the second power cable receptacle at the rear of the appliance. (See item 14 in Figure 2.)

Step 6

Press the power control button on the front of the appliance. (See item 2 in Figure 1.)

Establishing a Console Connection

You must establish a serial console connection to the appliance as part of the initial configuration process.

Attach the RS-232 cable to the console serial socket (see item 1 in Figure 2) and the other end of RS-232 cable to a console.

Connect the monitor and keyboard cables to the corresponding appliance sockets. (See items 2 and 3 in Figure 2.) You can also connect a mouse. (See item 4 in Figure 2.)

Step 2

Open the terminal emulation application on your PC to access the appliance CLI. The following procedure uses HyperTerminal for Windows:

Enter a name for your session in the Name field, for example "Cisco Guard," and then click OK.

In the Connect Using field, select the COM port to which the device is connected, and then click OK.

If this is the first time that you are connecting to the appliance, you must configure passwords for the system user accounts (root, admin, and riverhead). (See the "Configuring Passwords for System User Accounts", section for more information.

Step 5

After you create a session, you can save the connection settings for future use by choosing File > Save as.

You need to save the console connection settings only once on any given PC. Saving the console connection settings enables you to connect to the appliance CLI directly, without repeating the configuration steps. The next time you launch HyperTerminal, the session is listed as an option under Start > Programs > Accessories > HyperTerminal > Name_of_session.

Configuring Passwords for System User Accounts

The appliance has preconfigured system users. You must set passwords for the system users when you log in for the first time.

To configure the passwords for the system user accounts, perform the following steps:

The password must have a minimum length of six characters and should be a combination of letters and numbers. Retype the new password to verify it.

Note You can change the passwords for the admin and riverhead usernames at any time by using the password command.

Step 5

To enter the appliance CLI, enter admin for the username and enter the password you have configured in Step 3.

Technical Specifications

Table 3 Rack-Mount Specifications
Item	Specification
Dimensions
Weight	62 lbs (28.12 kg)
Height	3.36 inches (85.4 mm)
Width	17.5 inches (443.6 mm), 19 inches rack mountable
Depth	27.48 inches (698 mm)
Form Factor	Rack mount 2U
Power management
Power supply	350 Watts
Power supply type	100-240VAC volt universal auto setting
Interfaces
Out-of-Band	Two 10/100/1000BASE-T
In-Band	One dual-port NIC consisting of one of the following options: •Two Auto sense full/half duplex 10/100/1000 BASE-T (copper) •Two 1000BASE-SX (fiber)
Serial port	Two serial DB9 RS-232 ports
Electrical
	100-240 VAC auto-sense auto switch 50-60 Hz (Optional—A dual power supply)

Related Documentation

For configuration information on the Guard, refer to the following publications:

For configuration information on the Detector, refer to the following publications:

Translated Safety Warnings

This section repeats in multiple languages the basic warnings appropriate for the Cisco Guard and a Traffic Anomaly Detector appliance.

Power Disconnection Warning—Statement 1


Warning	Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.
Waarschuwing	Voordat u aan een systeem werkt dat een aan/uit schakelaar heeft, dient u de stroomvoorziening UIT te schakelen en de stekker van het netsnoer uit het stopcontact te halen.
Varoitus	Ennen kuin teet mit��n sellaiselle j�rjestelm�lle, jossa on kaksiasentokytkin, katkaise siit� virta ja kytke virtajohto irti.
Attention	Avant de travailler sur un syst�me �quip� d'un commutateur marche-arr�t, mettre l'appareil � l'arr�t (OFF) et d�brancher le cordon d'alimentation.
Warnung	Bevor Sie an einem System mit Ein/Aus-Schalter arbeiten, schalten Sie das System AUS und ziehen das Netzkabel aus der Steckdose.
Avvertenza	Prima di lavorare su un sistema dotato di un interruttore on/off, spegnere (OFF) il sistema e staccare il cavo dell'alimentazione.
Advarsel	Sl� AV str�mmen og trekk ut str�mledningen f�r det utf�res arbeid p� et system som er utstyrt med en av/p�-bryter.
Aviso	Antes de come�ar a trabalhar num sistema que tem um interruptor on/off, DESLIGUE a corrente el�ctrica e retire o cabo de alimenta��o da tomada.
�Advertencia!	Antes de utilizar cualquier sistema equipado con interruptor de Encendido/Apagado (ON/OFF), cortar la alimentaci�n y desenchufar el cable de alimentaci�n.
Varning!	Sl� AV str�mmen och dra ur n�tsladden innan du utf�r arbete p� ett system med str�mbrytare.

Installation Warning—Statement 10

Power Cord Warning—Statement 14

Warning	Read the installation instructions before you connect the system to its power source.
Waarschuwing	Raadpleeg de installatie-aanwijzingen voordat u het systeem met de voeding verbindt.
Varoitus	Lue asennusohjeet ennen j�rjestelm�n yhdist�mist� virtal�hteeseen.
Attention	Avant de brancher le syst�me sur la source d'alimentation, consulter les directives d'installation.
Warnung	Lesen Sie die Installationsanweisungen, bevor Sie das System an die Stromquelle anschlie�en.
Avvertenza	Consultare le istruzioni di installazione prima di collegare il sistema all'alimentatore.
Advarsel	Les installasjonsinstruksjonene f�r systemet kobles til str�mkilden.
Aviso	Leia as instru��es de instala��o antes de ligar o sistema � sua fonte de energia.
�Advertencia!	Ver las instrucciones de instalaci�n antes de conectar el sistema a la red de alimentaci�n.
Varning!	L�s installationsanvisningarna innan du kopplar systemet till dess str�mf�rs�rjningsenhet.


Warning	This unit might have more than one power cord. To reduce the risk of electric shock, disconnect the two power supply cords before servicing the unit.
Waarschuwing	Dit toestel kan meer dan ��n netsnoer hebben. Om het risico van een elektrische schok te verminderen, dient u de stekkers van de twee netsnoeren uit het stopcontact te halen voordat u het toestel een servicebeurt geeft.
Varoitus	T�ss� laitteessa saattaa olla useampi kuin yksi virtajohto. Irrota molemmat virtal�hteest� tulevat johtimet ennen laitteen huoltamista, jotta v�lt�t s�hk�iskun vaaran.
Attention	Il est possible que cette unit� soit munie de plusieurs cordons d'alimentation. Pour �viter les risques d'�lectrocution, d�brancher les deux cordons d'alimentation avant de r�parer l'unit�.
Warnung	Diese Einheit hat m�glicherweise mehr als ein Netzkabel. Zur Verringerung der Stromschlaggefahr trennen Sie beide Netzger�tekabel ab, bevor Sie die Einheit warten.
Avvertenza	Questa unit� potrebbe essere dotata di pi� di un cavo di alimentazione. Per ridurre il rischio di scossa elettrica, scollegare i due cavi di alimentazione prima di procedere alla manutenzione dell'unit�.
Advarsel	Denne enheten kan v�re utstyrt med mer enn �n str�mledning. Koble fra de to str�mledningene f�r det utf�res reparasjonsarbeid p� enheten for � redusere faren for elektriske st�t.
Aviso	Esta unidade poder� ter mais do que um cabo de alimenta��o. Para reduzir o risco de choque el�ctrico, desligue os dois cabos de alimenta��o antes de efectuar repara��es na unidade.
�Advertencia!	Puede ser que este equipo posea m�s de un cable de alimentaci�n. Para reducir el riesgo de descarga el�ctrica, desenchufar los dos cables antes de proceder al mantenimiento de la unidad.
Varning!	Denna enhet kan vara f�rsedd med mer �n en n�tsladd. F�r att minska risken f�r elektriska st�tar skall b�da n�tsladdarna dras ur innan du utf�r underh�llsarbete p� enheten.

SELV Circuit Warning—Statement 22


Warning	The ports labeled "Ethernet," "10BaseT," "Token Ring," "Console," and "AUX" are safety extra-low voltage (SELV) circuits. SELV circuits should only be connected to other SELV circuits. Because the BRI circuits are treated like telephone-network voltage, avoid connecting the SELV circuit to the telephone network voltage (TNV) circuits.
Waarschuwing	De poorten die "Ethernet", "10BaseT", "Token Ring", "Console" en "AUX" zijn gelabeld, zijn veiligheidscircuits met extra lage spanning (genaamd SELV = Safety Extra-Low Voltage). SELV-circuits mogen alleen met andere SELV-circuits verbonden worden. Omdat de BRI-circuits op dezelfde manier als telefoonnetwerkspanning behandeld worden, mag u het SELV-circuit niet verbinden met de telefoonnetwerkspanning (TNV) circuits.
Varoitus	Portit, joissa on nimet "Ethernet", "10BaseT", "Token Ring", "Console" ja "AUX", ovat erityisen pienen j�nnityksen omaavia turvallisuuspiirej� (SELV-piirej�). T�llaiset SELV-piirit tulee yhdist�� ainoastaan muihin SELV-piireihin. Koska perusluokan liit�nt�jen (Basic Rate Interface- eli BRI-liit�nn�t) j�nnite vastaa puhelinverkoston j�nnitett�, v�lt� SELV-piirin yhdist�mist� puhelinverkoston j�nnitepiireihin (TNV-piireihin).
Attention	Les ports �tiquet�s � Ethernet �, � 10BaseT �, � Token Ring �, � Console � et � AUX � sont des circuits de s�curit� basse tension (Safety Extra-Low Voltage ou SELV). Les circuits SELV ne doivent �tre interconnect�s qu'avec d'autres circuits SELV. Comme les circuits BRI sont consid�r�s comme des sources de tension de r�seau t�l�phonique, �viter de connecter un circuit SELV � un circuit de tension de r�seau t�l�phonique (telephone network voltage ou TNV).
Warnung	Die mit "Ethernet", "10BaseT", "Token Ring", "Console" und "AUX" beschrifteten Buchsen sind Sicherheitskreise mit Sicherheitskleinspannung (Safety Extra-Low Voltage, SELV). SELV-Kreise sollten ausschlie�lich an andere SELV-Kreise angeschlossen werden. Da die BRI-Kreise wie Telefonnetzspannungen behandelt werden, ist der SELV-Kreis nicht an Telefonnetzspannungskreise (TNV) anzuschlie�en.
Avvertenza	Le porte contrassegnate da "Ethernet", "10BaseT", "TokenRing", "Console" e "AUX" sono circuiti di sicurezza con tensione molto bassa (SELV). I circuiti SELV devono essere collegati solo ad altri circuiti SELV. Dato che i circuiti BRI vengono trattati come tensioni di rete telefonica, evitare di collegare il circuito SELV ai circuiti in cui � presente le tensione di rete telefonica (TNV).
Advarsel	Utgangene merket "Ethernet", "10BaseT", "Token Ring", "Console" og "AUX" er lavspentkretser (SELV) for ekstra sikkerhet. SELV-kretser skal kun kobles til andre SELV-kretser. Fordi BRI-kretsene h�ndteres som telenettspenning, unng� � koble SELV-kretsen til kretser for telenettspenning (TNV).
Aviso	As portas "Ethernet", "10BaseT", "Token Ring", "Console", and "AUX" s�o circuitos de seguran�a de baixa tens�o (SELV). Estes circuitos dever�o ser apenas ligados a outros circuitos SELV. Devido ao facto de os circuitos BRI (Interface de Ritmo B�sico) serem tratados como sendo de tens�o equivalente � da rede telef�nica, evite ligar o circuito SELV aos circuitos TNV (tens�o de rede telef�nica).
�Advertencia!	Los puertos "Ethernet", "10BaseT", "Token Ring", "Console" y "AUX" son circuitos de muy baja se�al que garantizan ausencia de peligro (Safety Extra-Low Voltage = SELV). Estos circuitos SELV deben ser conectados exclusivamente con otros tambi�n de tipo SELV. Puesto que los circuitos tipo BRI se comportan como aqu�llos con voltajes de red telef�nica, debe evitarse conectar circuitos SELV con circuitos de voltaje de red telef�nica (TNV).
Varning!	De portar som �r m�rkta "Ethernet", "10BaseT", "Token Ring", "Console" och "AUX" �r SELV-kretsar, d.v.s. skyddskretsar med extra l�g sp�nning (SELV: Safety Extra-Low Voltage = skyddsklensp�nning). SELV-kretsar f�r endast anslutas till andra SELV-kretsar. Eftersom BRI-kretsar behandlas liksom telefonn�tssp�nning b�r SELV-kretsen inte anslutas till telefonn�tssp�nningskretsar (TNV-kretsar).

Jewelry Removal Warning—Statement 43


Warning	Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.
Waarschuwing	Alvorens aan apparatuur te werken die met elektrische leidingen is verbonden, sieraden (inclusief ringen, kettingen en horloges) verwijderen. Metalen voorwerpen worden warm wanneer ze met stroom en aarde zijn verbonden, en kunnen ernstige brandwonden veroorzaken of het metalen voorwerp aan de aansluitklemmen lassen.
Varoitus	Ennen kuin ty�skentelet voimavirtajohtoihin kytkettyjen laitteiden parissa, ota pois kaikki korut (sormukset, kaulakorut ja kellot mukaan lukien). Metalliesineet kuumenevat, kun ne ovat yhteydess� s�hk�virran ja maan kanssa, ja ne voivat aiheuttaa vakavia palovammoja tai hitsata metalliesineet kiinni liit�nt�napoihin.
Attention	Avant d'acc�der � cet �quipement connect� aux lignes �lectriques, �ter tout bijou (anneaux, colliers et montres compris). Lorsqu'ils sont branch�s � l'alimentation et reli�s � la terre, les objets m�talliques chauffent, ce qui peut provoquer des blessures graves ou souder l'objet m�tallique aux bornes.
Warnung	Vor der Arbeit an Ger�ten, die an das Netz angeschlossen sind, jeglichen Schmuck (einschlie�lich Ringe, Ketten und Uhren) abnehmen. Metallgegenst�nde erhitzen sich, wenn sie an das Netz und die Erde angeschlossen werden, und k�nnen schwere Verbrennungen verursachen oder an die Anschlu�klemmen angeschwei�t werden.
Avvertenza	Prima di intervenire su apparecchiature collegate alle linee di alimentazione, togliersi qualsiasi monile (inclusi anelli, collane, braccialetti ed orologi). Gli oggetti metallici si riscaldano quando sono collegati tra punti di alimentazione e massa: possono causare ustioni gravi oppure il metallo pu� saldarsi ai terminali.
Advarsel	Fjern alle smykker (inkludert ringer, halskjeder og klokker) f�r du skal arbeide p� utstyr som er koblet til kraftledninger. Metallgjenstander som er koblet til kraftledninger og jord blir sv�rt varme og kan for�rsake alvorlige brannskader eller smelte fast til polene.
Aviso	Antes de trabalhar em equipamento que esteja ligado a linhas de corrente, retire todas as j�ias que estiver a usar (incluindo an�is, fios e rel�gios). Os objectos met�licos aquecer�o em contacto com a corrente e em contacto com a liga��o � terra, podendo causar queimaduras graves ou ficarem soldados aos terminais.
�Advertencia!	Antes de operar sobre equipos conectados a l�neas de alimentaci�n, quitarse las joyas (incluidos anillos, collares y relojes). Los objetos de metal se calientan cuando se conectan a la alimentaci�n y a tierra, lo que puede ocasionar quemaduras graves o que los objetos met�licos queden soldados a los bornes.
Varning!	Tag av alla smycken (inklusive ringar, halsband och armbandsur) innan du arbetar p� utrustning som �r kopplad till kraftledningar. Metallobjekt hettas upp n�r de kopplas ihop med str�m och jord och kan f�rorsaka allvarliga br�nnskador; metallobjekt kan ocks� sammansvetsas med kontakterna.

Safety Cover Requirement—Statement 117


Warning	The safety cover is an integral part of the product. Do not operate the unit without the safety cover installed. Operating the unit without the cover in place will invalidate the safety approvals and pose a risk of fire and electrical hazards.
Waarschuwing	Het beveiligingsdeksel is een integraal onderdeel van het product. Deze eenheid niet bedienen als het beveiligingsdeksel niet ge�nstalleerd is. Als het deksel niet op zijn plaats is tijdens de bediening, zal dit de veiligheidsaanbevelingen ongeldig maken en een risico op brand en elektrische gevaren vormen.
Varoitus	Suojakansi on t�rke� osa tuotetta. Yksikk�� ei saa k�ytt�� ilman suojakantta. Yksik�n k�ytt� ilman suojakantta mit�t�i turvallisuushyv�ksynn�t ja aiheuttaa tulipalon ja s�hk�iskun vaaran.
Attention	Le plateau de s�curit� est une partie int�grante du produit. Pour �viter tout risque de feu ou d'accident �lectrique, n'utilisez jamais l'unit� lorsque ce plateau n'est pas install�. Les garanties de s�curit� seraient annul�es.
Warnung	Die Sicherheitsabdeckung ist integraler Bestandteil des Produkts. Die Einheit darf nicht ohne installierte Sicherheitsabdeckung betrieben werden. Ein Betreiben der Einheit ohne korrekt installierte Abdeckung verst��t gegen die Sicherheitsnormen und f�hrt zu Brandgefahr sowie elektrischen Sicherheitsrisiken.
Avvertenza	Attenzione: Il pannello di sicurezza � parte integrante del prodotto. Non fate funzionare il sistema senza il pannello di sicurezza. Far funzionare il sistema senza il pannello invalider� le certificazioni di sicurezza e pu�'dare luogo a rischi di incendio e a cortocircuiti.
Advarsel	Dette sikkerhetsdekselet er en integral del av produktet. Enheten skal ikke brukes uten at sikkerhetsdekselet er montert. Bruk av enheten uten at sikkerhetsdekselet sitter p� plass, vil ugyldiggj�re sikkerhetsgodkjenningene, og kan dessuten utgj�re fare for brann og faremomenter i forbindelse med elektrisitet.
Aviso	A cobertura de seguran�a � uma parte integral do produto. N�o opere a unidade sem a respectiva cobertura de seguran�a instalada. Operar a unidade sem esta cobertura anular� as aprova��es de seguran�a e constituir� um risco de inc�ndio e perigo el�ctrico.
�Advertencia!	La cubierta de seguridad forma parte integral del producto. No haga funcionar este producto sin la cubierta de seguridad instalada, de lo contrario se invalidar�an las aprobaciones de seguridad y se correr�a el riesgo de incendio o de descargas el�ctricas.
Varning!	Skyddshuven �r en v�sentlig del av produkten. Anv�nd inte enheten utan installerad skyddshuv. Om enheten anv�nds utan skyddshuven p� plats upph�vs alla s�kerhetsgodk�nnanden och risk f�r brandfara och elektrisk fara f�religger.

Unit Grounding Protection Warning—Statement 213


Warning	Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.
Waarschuwing	De aardingsleiding mag nooit buiten werking gesteld worden en de apparatuur mag nooit bediend worden zonder dat er een op de juiste wijze ge�nstalleerde aardingsleiding aanwezig is. Neem contact op met de bevoegde instantie voor elektrische inspecties of met een elektricien als u niet zeker weet of voor passende aarding gezorgd is.
Varoitus	�l� koskaan ohita maajohdinta tai k�yt� laitteita ilman oikein asennettua maajohdinta. Ota yhteytt� asianmukaiseen s�hk�tarkastusviranomaiseen tai s�hk�asentajaan, jos olet ep�varma maadoituksen sopivuudesta.
Attention	Ne jamais rendre inop�rant le conducteur de masse ni utiliser l'�quipement sans un conducteur de masse ad�quatement install�. En cas de doute sur la mise � la masse appropri�e disponible, s'adresser � l'organisme responsable de la s�curit� �lectrique ou � un �lectricien.
Warnung	Umgehen Sie auf keinen Fall den Erdungsleiter und nehmen Sie die Ger�te nicht in Betrieb, wenn der Erdungsleiter nicht sachgem�� installiert ist. Wenden Sie sich an die entsprechende Beh�rde, die f�r die Inspektion elektrischer Anlagen zust�ndig ist, oder an einen Elektriker, wenn Sie nicht sicher sind, ob der Anschlu� ordnungsgem�� geerdet ist.
Avvertenza	Non escludere mai il conduttore di protezione n� usare l'apparecchiatura in assenza di un conduttore di protezione installato in modo corretto. Se non si sa con certezza che � disponibile un collegamento di messa a terra adeguato, esaminare le Norme CEI pertinenti o rivolgersi a un elettricista qualificato.
Advarsel	Jordingslederen m� aldri hindres, og utstyret m� aldri brukes uten at en forsvarlig jordingsleder er installert. Kontakt elektrisitetstilsynet eller en elektriker dersom du er usikker p� om riktig jording er tilgjengelig.
Aviso	Nunca anule o condutor � terra nem opere o equipamento sem ter um condutor � terra adequadamente instalado. Em caso de d�vida em rela��o ao sistema de liga��o � terra, contacte os servi�os locais de inspec��o el�ctrica ou um electricista qualificado.
�Advertencia!	No desactive nunca el conductor de tierra ni opere el equipo sin un conductor de tierra instalado correctamente. P�ngase en contacto con las autoridades de inspecci�n el�ctrica pertinentes o con un electricista, si no est� seguro de contar con una toma de tierra adecuada.
Varning!	Koppla aldrig fr�n jordledningen och anv�nd aldrig utrustningen utan en p� l�mpligt s�tt installerad jordledning. Om det f�religger os�kerhet huruvida l�mplig jordning finns skall elektrisk besiktningsauktoritet eller elektriker kontaktas.

AC Power Disconnection Warning—Statement 246

Work During Lightning Activity—Statement 1001

Warning	Before working on a chassis or working near power supplies, unplug the power cord on AC units.
Waarschuwing	Voordat u aan een frame of in de nabijheid van voedingen werkt, dient u bij wisselstroom toestellen de stekker van het netsnoer uit het stopcontact te halen.
Varoitus	Kytke irti vaihtovirtalaitteiden virtajohto ennen kuin teet mit��n asennuspohjalle tai ty�skentelet virtal�hteiden l�heisyydess�.
Attention	Avant de travailler sur un ch�ssis ou � proximit� d'une alimentation �lectrique, d�brancher le cordon d'alimentation des unit�s en courant alternatif.
Warnung	Bevor Sie an einem Chassis oder in der N�he von Netzger�ten arbeiten, ziehen Sie bei Wechselstromeinheiten das Netzkabel ab.
Avvertenza	Prima di lavorare su un telaio o intorno ad alimentatori, scollegare il cavo di alimentazione sulle unit� CA.
Advarsel	F�r det utf�res arbeid p� kabinettet eller det arbeides i n�rheten av str�mforsyningsenheter, skal str�mledningen trekkes ut p� vekselstr�msenheter.
Aviso	Antes de trabalhar num chassis, ou antes de trabalhar perto de unidades de fornecimento de energia, desligue o cabo de alimenta��o nas unidades de corrente alternada.
�Advertencia!	Antes de manipular el chasis de un equipo o trabajar cerca de una fuente de alimentaci�n, desenchufar el cable de alimentaci�n en los equipos de corriente alterna (CA).
Varning!	Innan du arbetar med ett chassi eller n�ra str�mf�rs�rjningsenheter skall du dra ur n�tsladden p� v�xelstr�msenheter.


Warning	Do not work on the system or connect or disconnect cables during periods of lightning activity.
Waarschuwing	Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te werken of kabels aan te sluiten of te ontkoppelen.
Varoitus	�l� ty�skentele j�rjestelm�n parissa �l�k� yhdist� tai irrota kaapeleita ukkosilmalla.
Attention	Ne pas travailler sur le syst�me ni brancher ou d�brancher les c�bles pendant un orage.
Warnung	Arbeiten Sie nicht am System und schlie�en Sie keine Kabel an bzw. trennen Sie keine ab, wenn es gewittert.
Avvertenza	Non lavorare sul sistema o collegare oppure scollegare i cavi durante un temporale con fulmini.
Advarsel	Utf�r aldri arbeid p� systemet, eller koble kabler til eller fra systemet n�r det tordner eller lyner.
Aviso	N�o trabalhe no sistema ou ligue e desligue cabos durante per�odos de mau tempo (trovoada).
�Advertencia!	No operar el sistema ni conectar o desconectar cables durante el transcurso de descargas el�ctricas en la atm�sfera.
Varning!	Vid �ska skall du aldrig utf�ra arbete p� systemet eller ansluta eller koppla loss kablar.

Chassis Warning for Rack-Mounting and Servicing—Statement 1006


Warning	To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: •This unit should be mounted at the bottom of the rack if it is the only unit in the rack. •When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. •If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.
Waarschuwing	Om lichamelijk letsel te voorkomen wanneer u dit toestel in een rek monteert of het daar een servicebeurt geeft, moet u speciale voorzorgsmaatregelen nemen om ervoor te zorgen dat het toestel stabiel blijft. De onderstaande richtlijnen worden verstrekt om uw veiligheid te verzekeren: •Dit toestel dient onderaan in het rek gemonteerd te worden als het toestel het enige in het rek is. •Wanneer u dit toestel in een gedeeltelijk gevuld rek monteert, dient u het rek van onderen naar boven te laden met het zwaarste onderdeel onderaan in het rek. •Als het rek voorzien is van stabiliseringshulpmiddelen, dient u de stabilisatoren te monteren voordat u het toestel in het rek monteert of het daar een servicebeurt geeft.
Varoitus	Kun laite asetetaan telineeseen tai huolletaan sen ollessa telineess�, on noudatettava erityisi� varotoimia j�rjestelm�n vakavuuden s�ilytt�miseksi, jotta v�ltyt��n loukkaantumiselta. Noudata seuraavia turvallisuusohjeita: •Jos telineess� ei ole muita laitteita, aseta laite telineen alaosaan. •Jos laite asetetaan osaksi t�ytettyyn telineeseen, aloita kuormittaminen sen alaosasta kaikkein raskaimmalla esineell� ja siirry sitten sen yl�osaan. •Jos telinett� varten on vakaimet, asenna ne ennen laitteen asettamista telineeseen tai sen huoltamista siin�.
Attention	Pour �viter toute blessure corporelle pendant les op�rations de montage ou de r�paration de cette unit� en casier, il convient de prendre des pr�cautions sp�ciales afin de maintenir la stabilit� du syst�me. Les directives ci-dessous sont destin�es � assurer la protection du personnel�: •Si cette unit� constitue la seule unit� mont�e en casier, elle doit �tre plac�e dans le bas. •Si cette unit� est mont�e dans un casier partiellement rempli, charger le casier de bas en haut en pla�ant l'�l�ment le plus lourd dans le bas. •Si le casier est �quip� de dispositifs stabilisateurs, installer les stabilisateurs avant de monter ou de r�parer l'unit� en casier.
Warnung	Zur Vermeidung von K�rperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell m�ssen Sie besondere Vorkehrungen treffen, um sicherzustellen, da� das System stabil bleibt. Die folgenden Richtlinien sollen zur Gew�hrleistung Ihrer Sicherheit dienen: •Wenn diese Einheit die einzige im Gestell ist, sollte sie unten im Gestell angebracht werden. •Bei Anbringung dieser Einheit in einem zum Teil gef�llten Gestell ist das Gestell von unten nach oben zu laden, wobei das schwerste Bauteil unten im Gestell anzubringen ist. •Wird das Gestell mit Stabilisierungszubeh�r geliefert, sind zuerst die Stabilisatoren zu installieren, bevor Sie die Einheit im Gestell anbringen oder sie warten.
Avvertenza	Per evitare infortuni fisici durante il montaggio o la manutenzione di questa unit� in un supporto, occorre osservare speciali precauzioni per garantire che il sistema rimanga stabile. Le seguenti direttive vengono fornite per garantire la sicurezza personale: •Questa unit� deve venire montata sul fondo del supporto, se si tratta dell'unica unit� da montare nel supporto. •Quando questa unit� viene montata in un supporto parzialmente pieno, caricare il supporto dal basso all'alto, con il componente pi� pesante sistemato sul fondo del supporto. •Se il supporto � dotato di dispositivi stabilizzanti, installare tali dispositivi prima di montare o di procedere alla manutenzione dell'unit� nel supporto.
Advarsel	Unng� fysiske skader under montering eller reparasjonsarbeid p� denne enheten n�r den befinner seg i et kabinett. V�r n�ye med at systemet er stabilt. F�lgende retningslinjer er gitt for � verne om sikkerheten: •Denne enheten b�r monteres nederst i kabinettet hvis dette er den eneste enheten i kabinettet. •Ved montering av denne enheten i et kabinett som er delvis fylt, skal kabinettet lastes fra bunnen og opp med den tyngste komponenten nederst i kabinettet. •Hvis kabinettet er utstyrt med stabiliseringsutstyr, skal stabilisatorene installeres f�r montering eller utf�ring av reparasjonsarbeid p� enheten i kabinettet.
Aviso	Para se prevenir contra danos corporais ao montar ou reparar esta unidade numa estante, dever� tomar precau��es especiais para se certificar de que o sistema possui um suporte est�vel. As seguintes directrizes ajud�-lo-�o a efectuar o seu trabalho com seguran�a: •Esta unidade dever� ser montada na parte inferior da estante, caso seja esta a �nica unidade a ser montada. •Ao montar esta unidade numa estante parcialmente ocupada, coloque os itens mais pesados na parte inferior da estante, arrumando-os de baixo para cima. •Se a estante possuir um dispositivo de estabiliza��o, instale-o antes de montar ou reparar a unidade.
�Advertencia!	Para evitar lesiones durante el montaje de este equipo sobre un bastidor, o posteriormente durante su mantenimiento, se debe poner mucho cuidado en que el sistema quede bien estable. Para garantizar su seguridad, proceda seg�n las siguientes instrucciones: •Colocar el equipo en la parte inferior del bastidor, cuando sea la �nica unidad en el mismo. •Cuando este equipo se vaya a instalar en un bastidor parcialmente ocupado, comenzar la instalaci�n desde la parte inferior hacia la superior colocando el equipo m�s pesado en la parte inferior. •Si el bastidor dispone de dispositivos estabilizadores, instalar �stos antes de montar o proceder al mantenimiento del equipo instalado en el bastidor.
Varning!	F�r att undvika kroppsskada n�r du installerar eller utf�r underh�llsarbete p� denna enhet p� en st�llning m�ste du vidta s�rskilda f�rsiktighets�tg�rder f�r att f�rs�kra dig om att systemet st�r stadigt. F�ljande riktlinjer ges f�r att trygga din s�kerhet: •Om denna enhet �r den enda enheten p� st�llningen skall den installeras l�ngst ned p� st�llningen. •Om denna enhet installeras p� en delvis fylld st�llning skall st�llningen fyllas nedifr�n och upp, med de tyngsta enheterna l�ngst ned p� st�llningen. •Om st�llningen �r f�rsedd med stabiliseringsdon skall dessa monteras fast innan enheten installeras eller underh�lls p� st�llningen.





Aviso	Para evitar les�es corporais ao montar ou dar manuten��o a esta unidade em um rack, � necess�rio tomar todas as precau��es para garantir a estabilidade do sistema. As seguintes orienta��es s�o fornecidas para garantir a sua seguran�a: •Se esta for a �nica unidade, ela dever� ser montada na parte inferior do rack. •Ao montar esta unidade em um rack parcialmente preenchido, carregue-o de baixo para cima com o componente mais pesado em sua parte inferior. •Se o rack contiver dispositivos estabilizadores, instale-os antes de montar ou dar manuten��o � unidade existente.
Advarsel	For at forhindre legemesbeskadigelse ved montering eller service af denne enhed i et rack, skal du sikre at systemet st�r stabilt. F�lgende retningslinjer er ogs� for din sikkerheds skyld: •Enheden skal monteres i bunden af dit rack, hvis det er den eneste enhed i racket. •Ved montering af denne enhed i et delvist fyldt rack, skal enhederne installeres fra bunden og opad med den tungeste enhed nederst. •Hvis racket leveres med stabiliseringsenheder, skal disse installeres for enheden monteres eller serviceres i racket.

Battery Handling—Statement 1015


Warning	There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
Waarschuwing	Er is ontploffingsgevaar als de batterij verkeerd vervangen wordt. Vervang de batterij slechts met hetzelfde of een equivalent type dat door de fabrikant aanbevolen is. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften weggeworpen te worden.
Varoitus	R�j�hdyksen vaara, jos akku on vaihdettu v��r��n akkuun. K�yt� vaihtamiseen ainoastaan saman- tai vastaavantyyppist� akkua, joka on valmistajan suosittelema. H�vit� k�ytetyt akut valmistajan ohjeiden mukaan.
Attention	Danger d'explosion si la pile n'est pas remplac�e correctement. Ne la remplacer que par une pile de type semblable ou �quivalent, recommand�e par le fabricant. Jeter les piles usag�es conform�ment aux instructions du fabricant.
Warnung	Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
Avvertenza	Pericolo di esplosione se la batteria non � installata correttamente. Sostituire solo con una di tipo uguale o equivalente, consigliata dal produttore. Eliminare le batterie usate secondo le istruzioni del produttore.
Advarsel	Det kan v�re fare for eksplosjon hvis batteriet skiftes p� feil m�te. Skift kun med samme eller tilsvarende type som er anbefalt av produsenten. Kasser brukte batterier i henhold til produsentens instruksjoner.
Aviso	Existe perigo de explos�o se a bateria for substitu�da incorrectamente. Substitua a bateria por uma bateria igual ou de um tipo equivalente recomendado pelo fabricante. Destrua as baterias usadas conforme as instru��es do fabricante.
�Advertencia!	Existe peligro de explosi�n si la bater�a se reemplaza de manera incorrecta. Reemplazar la bater�a exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante. Desechar las bater�as gastadas seg�n las instrucciones del fabricante.
Varning!	Explosionsfara vid felaktigt batteribyte. Ers�tt endast batteriet med samma batterityp som rekommenderas av tillverkaren eller motsvarande. F�lj tillverkarens anvisningar vid kassering av anv�nda batterier.

Blank Faceplates and Cover Panels—Statement 1029


Warning	Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.
Waarschuwing	Lege vlakplaten en afdekpanelen vervullen drie belangrijke functies: ze voorkomen blootstelling aan gevaarlijke voltages en stroom binnenin het frame, ze bevatten elektromagnetische storing (EMI) hetgeen andere apparaten kan verstoren en ze leiden de stroom van koellucht door het frame. Het systeem niet bedienen tenzij alle kaarten, vlakplaten en afdekkingen aan de voor- en achterkant zich op hun plaats bevinden.
Varoitus	Tyhjill� tasolaikoilla ja suojapaneeleilla on kolme t�rke�� k�ytt�tarkoitusta: Ne suojaavat asennuspohjan sis�isille vaarallisille j�nnitteille ja s�hk�virralle altistumiselta; ne pit�v�t sis�ll��n elektromagneettisen h�iri�n (EMI), joka voi h�irit� muita laitteita; ja ne suuntaavat tuuletusilman asennuspohjan l�pi. J�rjestelm�� ei saa k�ytt��, elleiv�t kaikki tasolaikat, etukannet ja takakannet ole kunnolla paikoillaan.
Attention	Ne jamais faire fonctionner le syst�me sans que l'int�gralit� des cartes, des plaques m�talliques et des panneaux avant et arri�re ne soient fix�s � leur emplacement. Ceux-ci remplissent trois fonctions essentielles : ils �vitent tout risque de contact avec des tensions et des courants dangereux � l'int�rieur du ch�ssis, ils �vitent toute diffusion d'interf�rences �lectromagn�tiques qui pourraient perturber le fonctionnement des autres �quipements, et ils canalisent le flux d'air de refroidissement dans le ch�ssis.
Warnung	Blanke Faceplates und Abdeckungen haben drei wichtigen Funktionen: (1) Sie sch�tzen vor gef�hrlichen Spannungen und Strom innerhalb des Chassis; (2) sie halten elektromagnetische Interferenzen (EMI) zur�ck, die andere Ger�te st�ren k�nnten; (3) sie lenken den k�hlenden Luftstrom durch das Chassis. Das System darf nur betrieben werden, wenn alle Karten, Faceplates, Voder- und R�ckabdeckungen an Ort und Stelle sind.
Avvertenza	Le piattaforme bianche e i panelli di protezione hanno tre funzioni importanti: Evitano l'esposizione a voltaggi e correnti elettriche pericolose nello chassis, trattengono le interferenze elettromagnetiche (EMI) che potrebbero scombussolare altri apparati e dirigono il flusso di aria per il raffreddamento attraverso lo chassis. Non mettete in funzione il sistema se le schede, le piattaforme, i panelli frontali e posteriori non sono in posizione.
Advarsel	Blanke ytterplater og deksler s�rger for tre viktige funksjoner: de forhindrer utsettelse for farlig spenning og str�m inni kabinettet; de inneholder elektromagnetisk forstyrrelse (EMI) som kan avbryte annet utstyr, og de dirigerer luftavkj�lingsstr�mmen gjennom kabinettet. Betjen ikke systemet med mindre alle kort, ytterplater, frontdeksler og bakdeksler sitter p� plass.
Aviso	As faces furadas e os pain�is de protec��o desempenham tr�s importantes fun��es: previnem contra uma exposi��o perigosa a voltagens e correntes existentes no interior do chassis; previnem contra interfer�ncia electromagn�tica (EMI) que poder� danificar outro equipamento; e canalizam o fluxo do ar de refrigera��o atrav�s do chassis. N�o dever� operar o sistema sem que todas as placas, faces, protec��es anteriores e posteriores estejam nos seus lugares.
�Advertencia!	Las placas frontales y los paneles de relleno cumplen tres funciones importantes: evitan la exposici�n a niveles peligrosos de voltaje y corriente dentro del chasis; reducen la interferencia electromagn�tica (EMI) que podr�a perturbar la operaci�n de otros equipos y dirigen el flujo de aire de enfriamiento a trav�s del chasis. No haga funcionar el sistema a menos que todas las tarjetas, placas frontales, cubiertas frontales y cubiertas traseras est�n en su lugar.
Varning!	Tomma framplattor och skyddspaneler har tre viktiga funktioner: de f�rhindrar att personer uts�tts f�r farlig sp�nning och str�m som finns inuti chassit; de inneh�ller elektromagnetisk interferens (EMI) som kan st�ra annan utrustning; och de styr riktningen p� kylluftsfl�det genom chassit. Anv�nd inte systemet om inte alla kort, framplattor, fram- och bakskydd �r p� plats.





Aviso	Plaquetas vazias e pain�is de prote��o t�m tr�s fun��es importantes: impedem a exposi��o a tens�es e correntes el�tricas perigosas dentro do chassi; apresentam interfer�ncia eletromagn�tica (EMI) que pode danificar outros equipamentos: direcionam o fluxo do ar refrigerado pelo chassi. N�o opere o sistema a menos que todas as placas, plaquetas, tampas frontais e tampas traseiras estejam em seu devido lugar.
Advarsel	Blanke frontplader og sidepaneler tjener tre vigtige form�l: de forhinder uds�ttelse for farlig sp�nding og str�m inde i chassiset, de isolerer elektromagnetisk interferens (EMI), der kan forstyre andet udstyr, og de leder en str�m af k�lig luft gennem chassiset. Betjen ikke systemet medmindre alle kort, frontplader, sidepaneler og bagpaneler er p� plads.

Equipment Installation—Statement 1030


Warning	Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Waarschuwing	Deze apparatuur mag alleen worden ge�nstalleerd, vervangen of hersteld door bevoegd geschoold personeel.
Varoitus	T�m�n laitteen saa asentaa, vaihtaa tai huoltaa ainoastaan koulutettu ja laitteen tunteva henkil�kunta.
Attention	Il est vivement recommand� de confier l'installation, le remplacement et la maintenance de ces �quipements � des personnels qualifi�s et exp�riment�s.
Warnung	Das Installieren, Ersetzen oder Bedienen dieser Ausr�stung sollte nur geschultem, qualifiziertem Personal gestattet werden.
Avvertenza	Questo apparato pu� essere installato, sostituito o mantenuto unicamente da un personale competente.
Advarsel	Bare oppl�rt og kvalifisert personell skal foreta installasjoner, utskiftninger eller service p� dette utstyret.
Aviso	Apenas pessoal treinado e qualificado deve ser autorizado a instalar, substituir ou fazer a revis�o deste equipamento.
�Advertencia!	Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.
Varning!	Endast utbildad och kvalificerad personal b�r f� till�telse att installera, byta ut eller reparera denna utrustning.





Aviso	Somente uma equipe treinada e qualificada tem permiss�o para instalar, substituir ou dar manuten��o a este equipamento.
Advarsel	Kun uddannede personer m� installere, udskifte komponenter i eller servicere dette udstyr.

Product Disposal—Statement 1040


Warning	Ultimate disposal of this product should be handled according to all national laws and regulations.
Waarschuwing	Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen.
Varoitus	T�m� tuote on h�vitett�v� kansallisten lakien ja m��r�ysten mukaisesti.
Attention	La mise au rebut ou le recyclage de ce produit sont g�n�ralement soumis � des lois et/ou directives de respect de l'environnement. Renseignez-vous aupr�s de l'organisme comp�tent.
Warnung	Die Entsorgung dieses Produkts sollte gem�� allen Bestimmungen und Gesetzen des Landes erfolgen.
Avvertenza	Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.
Advarsel	Endelig kassering av dette produktet skal v�re i henhold til alle relevante nasjonale lover og bestemmelser.
Aviso	Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais.
�Advertencia!	Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.
Varning!	Vid deponering hanteras produkten enligt g�llande lagar och best�mmelser.





Aviso	O descarte definitivo deste produto deve estar de acordo com todas as leis e regulamenta��es nacionais.
Advarsel	Endelig bortskaffelse af dette produkt skal ske i henhold til g�ldende love og regler.

Disconnecting Telephone-Network Cables—Statement 1041


Warning	Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network voltages.
Waarschuwing	Voordat u de eenheid opent, dient u de verbinding met het telefoonnetwerk te verbreken door de kabels te ontkoppelen om zo contact met telefoonnetwerk-spanning te vermijden.
Varoitus	V�lt� joutumista kosketuksiin puhelinverkkoj�nnitteiden kanssa irrottamalla puhelinverkoston kaapelit ennen yksik�n aukaisemista.
Attention	Pour �viter tout risque de choc �lectrique (tensions pr�sentes dans l'unit�), d�branchez les c�bles du r�seau t�l�phonique AVANT d'ouvrir l'unit�.
Warnung	Bevor Sie das Ger�t �ffnen, ziehen Sie die Telefonnetzkabel aus der Verbindung, um Kontakt mit Telefonnetzspannungen zu vermeiden.
Avvertenza	Prima di aprire l'unit�, scollegare i cavi della rete telefonica per evitare di entrare in contatto con la tensione di rete.
Advarsel	F�r enheten �pnes, skal kablene for telenettet kobles fra for � unng� � komme i kontakt med spenningen i telenettet.
Aviso	Antes de abrir a unidade, desligue os cabos da rede telef�nica para evitar contacto com a tens�o da respectiva rede.
�Advertencia!	Antes de abrir la unidad, desconectar el cableado dirigido a la red telef�nica para evitar contacto con voltajes de la propia red.
Varning!	Koppla loss ledningarna till telefonn�tet innan du �ppnar enheten s� att kontakten med telefonn�tssp�nningen bryts.

Short-circuit Protection—Statement 1045


Warning	This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations.
Waarschuwing	Voor dit product moet kortsluitbeveiliging (overstroombeveiliging) deel uitmaken van de installatie in het gebouw. De installatie moet voldoen aan de nationale en lokale bedradingvoorschriften.
Varoitus	T�m� tuote vaatii suojauksen oikosulkuja (ylivirtaa) vastaan osana asennusta rakennukseen. Asenna ainoastaan kansallisten ja paikallisten johdotuss��nn�sten mukaisesti.
Attention	La protection de ce produit contre les courts-circuits (surtensions) doit �tre assur�e par la configuration �lectrique du b�timent. V�rifiez que l'installation a lieu uniquement en conformit� avec les normes de c�blage en vigueur au niveau national et local.
Warnung	F�r dieses Produkt ist eine Kurzschlu�sicherung (�berstromsicherung) erforderlich, die als Teil der Geb�udeinstallation zur Verf�gung gestellt wird. Die Installation sollte nur in �bereinstimmung mit den nationalen und regionalen Vorschriften zur Verkabelung erfolgen.
Avvertenza	Questo prodotto richiede una protezione contro i cortocircuiti, da fornirsi come parte integrante delle dotazioni presenti nell'edificio. Effettuare l'installazione rispettando le Norme CEI pertinenti.
Advarsel	Dette produktet krever beskyttelse mot kortslutninger (overspenninger) som en del av installasjonen. Bare installer utstyret i henhold til nasjonale og lokale krav til ledningsnett.
Aviso	Este produto requer prote��o contra curto-circuitos (sobreintensidade de corrente), que deve estar instalada nos edif�cios. Instale apenas de acordo com as normas de instala��o el�trica nacionais e locais.
Advertencia	Este producto necesita estar conectado a la protecci�n frente a cortacircuitos (sobretensiones) que exista en el edificio. Inst�lelo �nicamente en conformidad con las regulaciones sobre cableado, tanto locales como nacionales, a las que se tenga que atener.
Varning!	Denna produkt kr�ver att kortslutningsskydd (�verstr�m) tillhandah�lles som en del av byggnadsinstallationen. Installera bara i enlighet med nationella och lokala kabeldragningsbest�mmelser.





Aviso	Este produto requer uma prote��o contra curto-circuito (sobrecorrente) que deve fazer parte da instala��o do edif�cio. Fa�a a instala��o somente de acordo com as regulamenta��es de cabeamento nacionais e locais.
Advarsel	Dette produkt kr�ver beskyttelse mod kortslutning (overstr�m). Dette skal v�re en del elinstallationen i bygningen. Installation skal ske i overensstemmelse med nationale og lokale ledningsregler.

Grounded Equipment—Statement 1064


Warning	This equipment is intended to be grounded to comply with emission and immunity requirements. Ensure that the switch functional ground lug is connected to earth ground during normal use.
Waarschuwing	Deze apparatuur dient geaard te worden in overeenstemming met emissie- en immuniteitsvereisten. Zorg dat de functionele verbindingsslip van de schakelaar geaard is tijdens normaal gebruik.
Varoitus	T�m� laite on tarkoitettu maadoitettavaksi s�teily- ja h�iri�nsietovaatimusten t�ytt�miseksi. Varmista, ett� kytkimen toiminnallinen maadoituskenk� on kytketty maadoitukseen normaalik�yt�n aikana.
Attention	Cet �quipement doit �tre reli� � la terre pour r�pondre aux exigences en mati�re d'�missions et d'immunit�. V�rifiez que la vis de mise � la terre fonctionnelle du commutateur est bien connect�e � la terre pendant l'exploitation de l'�quipement.
Warnung	Dieses Ger�t muss geerdet werden, um den Strahlungs- und St�rfestigkeitsbestimmungen zu entsprechen. Stellen Sie daher sicher, dass w�hrend des normalen Betriebs die Massenanschluss�se des Switches mit dem Erdleiter verbunden ist.
Avvertenza	Quest'apparecchiatura deve essere collegata a terra al fine di essere conforme ai requisiti di emissione e immunit�. Assicurarsi che il terminale di terra funzionale dello switch sia collegato a massa durante l'uso normale.
Advarsel	Dette utstyret er beregnet p� jording som samsvarer med kravene til utslipp og immunitet. P�se at bryterens funksjonelle jordingskabelsko er koblet til jording ved normal bruk.
Aviso	Este equipamento deve ser aterrado para atender aos requisitos de emiss�o e imunidade. Certifique-se de que o suporte de aterramento funcional do switch esteja conectado ao terra durante a opera��o normal.
�Advertencia!	Este equipo est� dise�ado para que se conecte a tierra de modo que cumpla con los requisitos de emisi�n e inmunidad. Aseg�rese de que el terminal de tierra funcional del switch est� conectado a tierra durante el uso normal.
Varning!	Denna utrustning b�r jordas f�r att uppfylla g�llande emissions- och immunitetskrav. Se till att omkopplarens funktionella jordningsfl�ns �r jordad under normal anv�ndning.

Warning Definition—Statement 1071


Warning	IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. SAVE THESE INSTRUCTIONS
Waarschuwing	BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen. BEWAAR DEZE INSTRUCTIES
Varoitus	T�RKEIT� TURVALLISUUSOHJEITA T�m� varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin k�sittelet laitteistoa, huomioi s�hk�piirien k�sittelemiseen liittyv�t riskit ja tutustu onnettomuuksien yleisiin ehk�isytapoihin. Turvallisuusvaroitusten k��nn�kset l�ytyv�t laitteen mukana toimitettujen k��nnettyjen turvallisuusvaroitusten joukosta varoitusten lopussa n�kyvien lausuntonumeroiden avulla. S�ILYT� N�M� OHJEET
Attention	IMPORTANTES INFORMATIONS DE S�CURIT� Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entra�ner des blessures ou des dommages corporels. Avant de travailler sur un �quipement, soyez conscient des dangers li�s aux circuits �lectriques et familiarisez-vous avec les proc�dures couramment utilis�es pour �viter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de s�curit� traduites qui accompagnent cet appareil, r�f�rez-vous au num�ro de l'instruction situ� � la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS
Warnung	WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen f�hren kann. Machen Sie sich vor der Arbeit mit Ger�ten mit den Gefahren elektrischer Schaltungen und den �blichen Verfahren zur Vorbeugung vor Unf�llen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen �bersetzung in den �bersetzten Sicherheitshinweisen, die zusammen mit diesem Ger�t ausgeliefert wurden. BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza	IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. CONSERVARE QUESTE ISTRUZIONI
Advarsel	VIKTIGE SIKKERHETSINSTRUKSJONER Dette advarselssymbolet betyr fare. Du er i en situasjon som kan f�re til skade p� person. F�r du begynner � arbeide med noe av utstyret, m� du v�re oppmerksom p� farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for � forhindre ulykker. Bruk nummeret i slutten av hver advarsel for � finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten. TA VARE P� DISSE INSTRUKSJONENE
Aviso	INSTRU��ES IMPORTANTES DE SEGURAN�A Este s�mbolo de aviso significa perigo. Voc� est� em uma situa��o que poder� ser causadora de les�es corporais. Antes de iniciar a utiliza��o de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos el�tricos e familiarize-se com as pr�ticas habituais de preven��o de acidentes. Utilize o n�mero da instru��o fornecido ao final de cada aviso para localizar sua tradu��o nos avisos de seguran�a traduzidos que acompanham este dispositivo. GUARDE ESTAS INSTRU��ES
�Advertencia!	INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este s�mbolo de aviso indica peligro. Existe riesgo para su integridad f�sica. Antes de manipular cualquier equipo, considere los riesgos de la corriente el�ctrica y familiar�cese con los procedimientos est�ndar de prevenci�n de accidentes. Al final de cada advertencia encontrar� el n�mero que le ayudar� a encontrar el texto traducido en el apartado de traducciones que acompa�a a este dispositivo. GUARDE ESTAS INSTRUCCIONES
Varning!	VIKTIGA S�KERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utf�r arbete p� n�gon utrustning m�ste du vara medveten om farorna med elkretsar och k�nna till vanliga f�rfaranden f�r att f�rebygga olyckor. Anv�nd det nummer som finns i slutet av varje varning f�r att hitta dess �vers�ttning i de �versatta s�kerhetsvarningar som medf�ljer denna anordning. SPARA DESSA ANVISNINGAR





Aviso	INSTRU��ES IMPORTANTES DE SEGURAN�A Este s�mbolo de aviso significa perigo. Voc� se encontra em uma situa��o em que h� risco de les�es corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos el�tricos e familiarize-se com as pr�ticas padr�o de preven��o de acidentes. Use o n�mero da declara��o fornecido ao final de cada aviso para localizar sua tradu��o nos avisos de seguran�a traduzidos que acompanham o dispositivo. GUARDE ESTAS INSTRU��ES
Advarsel	VIGTIGE SIKKERHEDSANVISNINGER Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. F�r du begynder arbejde p� udstyr, skal du v�re opm�rksom p� de involverede risici, der er ved elektriske kredsl�b, og du skal s�tte dig ind i standardprocedurer til undg�else af ulykker. Brug erkl�ringsnummeret efter hver advarsel for at finde overs�ttelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER

Comply with Local and National Electrical Codes—Statement 1074


Warning	Installation of the equipment must comply with local and national electrical codes.
Waarschuwing	Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale elektriciteitsvoorschriften.
Varoitus	Laitteisto tulee asentaa paikallisten ja kansallisten s�hk�m��r�ysten mukaisesti.
Attention	L'�quipement doit �tre install� conform�ment aux normes �lectriques nationales et locales.
Warnung	Die Installation der Ger�te muss den Sicherheitsstandards entsprechen.
Avvertenza	L'installazione dell'impianto deve essere conforme ai codici elettrici locali e nazionali.
Advarsel	Installasjon av utstyret m� samsvare med lokale og nasjonale elektrisitetsforskrifter.
Aviso	A instala��o do equipamento tem de estar em conformidade com os c�digos el�ctricos locais e nacionais.
�Advertencia!	La instalaci�n del equipo debe cumplir con las normativas de electricidad locales y nacionales.
Varning!	Installation av utrustningen m�ste ske i enlighet med g�llande elinstallationsf�reskrifter.

Obtaining Documentation

Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

Product Documentation DVD

The Product Documentation DVD is a comprehensive library of technical product documentation on a portable medium. The DVD enables you to access multiple versions of installation, configuration, and command guides for Cisco hardware and software products. With the DVD, you have access to the same HTML documentation that is found on the Cisco website without being connected to the Internet. Certain products also have .PDF versions of the documentation available.

The Product Documentation DVD is available as a single unit or as a subscription. Registered Cisco.com users (Cisco direct customers) can order a Product Documentation DVD (product number DOC-DOCDVD= or DOC-DOCDVD=SUB) from Cisco Marketplace at this URL:

Ordering Documentation

Registered Cisco.com users may order Cisco documentation at the Product Documentation Store in the Cisco Marketplace at this URL:

Nonregistered Cisco.com users can order technical documentation from 8:00 a.m. to 5:00 p.m. (0800 to 1700) PDT by calling 1 866 463-3487 in the United States and Canada, or elsewhere by calling 011 408 519-5055. You can also order documentation by e-mail at tech-doc-store-mkpl@external.cisco.com or by fax at 1 408 519-5001 in the United States and Canada, or elsewhere at 011 408 519-5001.

Documentation Feedback

You can rate and provide feedback about Cisco technical documents by completing the online feedback form that appears with the technical documents on Cisco.com.

You can submit comments about Cisco documentation by using the response card (if present) behind the front cover of your document or by writing to the following address:

Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883

Cisco Product Security Overview

A current list of security advisories, security notices, and security responses for Cisco products is available at this URL:

To see security advisories, security notices, and security responses as they are updated in real time, you can subscribe to the Product Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed. Information about how to subscribe to the PSIRT RSS feed is found at this URL:

Reporting Security Problems in Cisco Products

Cisco is committed to delivering secure products. We test our products internally before we release them, and we strive to correct all vulnerabilities quickly. If you think that you have identified a vulnerability in a Cisco product, contact PSIRT:

An emergency is either a condition in which a system is under active attack or a condition for which a severe and urgent security vulnerability should be reported. All other conditions are considered nonemergencies.

Tip

We encourage you to use Pretty Good Privacy (PGP) or a compatible product (for example, GnuPG) to encrypt any sensitive information that you send to Cisco. PSIRT can work with information that has been encrypted with PGP versions 2.x through 9.x.

Never use a revoked or an expired encryption key. The correct public key to use in your correspondence with PSIRT is the one linked in the Contact Summary section of the Security Vulnerability Policy page at this URL:

http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html

The link on this page has the current PGP key ID in use.

If you do not have or use PGP, contact PSIRT at the aforementioned e-mail addresses or phone numbers before sending any sensitive material to find other means of encrypting the data.

Obtaining Technical Assistance

Cisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco Technical Support & Documentation website on Cisco.com features extensive online support resources. In addition, if you have a valid Cisco service contract, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not have a valid Cisco service contract, contact your reseller.

Cisco Technical Support & Documentation Website

The Cisco Technical Support & Documentation website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, at this URL:

Access to all tools on the Cisco Technical Support & Documentation website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL:

Note Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting a web or phone request for service. You can access the CPI tool from the Cisco Technical Support & Documentation website by clicking the Tools & Resources link under Documentation & Tools. Choose Cisco Product Identification Tool from the Alphabetical Index drop-down list, or click the Cisco Product Identification Tool link under Alerts & RMAs. The CPI tool offers three search options: by product ID or model name; by tree view; or for certain products, by copying and pasting show command output. Search results show an illustration of your product with the serial number label location highlighted. Locate the serial number label on your product and record the information before placing a service call.

Submitting a Service Request

Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool provides recommended solutions. If your issue is not resolved using the recommended resources, your service request is assigned to a Cisco engineer. The TAC Service Request Tool is located at this URL:

For S1 or S2 service requests, or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.

Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447

Definitions of Service Request Severity

To ensure that all service requests are reported in a standard format, Cisco has established severity definitions.

Severity 1 (S1)—An existing network is down, or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.

Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your business operations are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.

Severity 3 (S3)—Operational performance of the network is impaired, while most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.

Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.

Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online and printed sources.

•

The Cisco Product Quick Reference Guide is a handy, compact reference tool that includes brief product overviews, key features, sample part numbers, and abbreviated technical specifications for many Cisco products that are sold through channel partners. It is updated twice a year and includes the latest Cisco offerings. To order and find out more about the Cisco Product Quick Reference Guide, go to this URL:

•

Cisco Marketplace provides a variety of Cisco books, reference guides, documentation, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL:

•

Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL:

•

Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments. Each quarter, Packet delivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions, as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores of in-depth online resources. You can access Packet magazine at this URL:

•

iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, using real-world case studies and business strategies to help readers make sound technology investment decisions. You can access iQ Magazine at this URL:

•

Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL:

•

Networking products offered by Cisco Systems, as well as customer support services, can be obtained at this URL:

•

Networking Professionals Connection is an interactive website for networking professionals to share questions, suggestions, and information about networking products and technologies with Cisco experts and other networking professionals. Join a discussion at this URL:

•

World-class networking training is available from Cisco. You can view current offerings at this URL:

Table Of Contents