Table of Contents

Quick Connect


Topology
Getting Help


Mounting


Status Lights

Trunk Port Status Lights


Ethernet Port Status Lights

Notice

FCC Registration Information
Industry Canada

Quick Reference
For The Cisco Access Analog Trunk Gateway

Quick Connect

Topology

Getting Help

For detailed installation configuration instructions, visit our Web site at the address above.

Documentation is also included on the product CD. Insert the CD and click System Guide to open the CD-ROM version of the Selsius System Guide.

Mounting

*The wall mount bracket is not included. Please contact your Cisco sales representative for more information.

Status Lights

Trunk Port Status Lights

Trunk port status lights show the status of individual trunk ports. The Gateway can have from two to eight ports for analog trunks.

Steady Off The port is in-service, but idle.

Steady On There is an active call on the port.

Flutter 2 seconds, 4 seconds off, repeat An inbound call is ringing.

Two flashes every 4 seconds The port is not configured at the CallManager (the Cisco Communications System server).

One flash every 4 seconds The port is configured at the CallManager, but no line battery voltage is detected. It is likely that the line is not connected at the CO or PBX, or there is a wiring break.

Ethernet Port Status Lights

Ethernet port status lights show the status of the port connected to the IP network.

Link A light indicates that the port is enabled and connected to another active port. If the light is off, this port is either not connected to an active port or the other port is disabled.

Ethernet RX A light indicates that the port is receiving Ethernet data.

Ethernet TX A light indicates that the port is transmitting data.

Heart Beat A light with a cadence of 1 second on, 1 second off indicates that the gateway is communicating with the CallManager. The light winks once every 2 seconds if the gateway is not communicating with the CallManager.

Notice

This device cannot be connected to the public switched telephone network (PSTN) in countries outside of North America.

FCC Registration Information

The Cisco Analog Access is in full compliance with Part 68 of the Federal Communication Commission's (FCC) rules and regulations. Cisco Analog Access complies with FCC Part 15, Subpart b, for a Class A computing device. In all matters regarding FCC registration and requirements of Appendix J of the FCC Form 730 Application Guide concerning Part 68 of the rules, the label information below is to be used (the label is on the back of the equipment) and the information will be provided to the telephone company if requested.

• Ringer Equivalence Number (REN) - 0.4B

• Required Connector - RJ-11C

• Authorized Network Ports - 02LS2

Further requirements are as follows:

• The Ringer Equivalence Number (REN) is used to determine the quantity of devices which may be connected to the telephone company lines. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total RENs contact the telephone company to determine the maximum REN for the calling area.

• If the Cisco Analog Access causes harm to the telephone network, the telephone company will notify the customer in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, the customer will be advised of the right to file a complaint with the FCC if it is believed to be necessary.

• The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for necessary modifications to be made to maintain uninterrupted services.

• If trouble is experienced with the Analog Access unit, please refer to Cisco Systems Limited Hardware Warranty for repair and/or warranty information. If the trouble is causing harm to the telephone network, the telephone company may request that the equipment be removed from the network until the problem is solved.

• Connection to Party Line Service is subject to state tariffs. (Contact the state public utility commission, public service commission, or corporate commission for information.)

• This equipment is capable of providing users access to interstate providers of operator services through the use of access codes. Modifications of this equipment by call aggregators to block access dialing codes is a violation of the Telephone Operator Consumers Act of 1990 and Part 68 of the FCC rules.

Industry Canada

Notice: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document (s). The Department does not guarantee the equipment will operate to the user's satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local Telecommunications Company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

Ringer Equivalence Number (REN) - 0.3

Posted: Thu Aug 9 02:18:04 PDT 2001
All contents are Copyright © 1992--2001 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.